Xerox Nuvera™ 100/120/144 Digital Production System - Customer Expectations Document
- 6 -
Envelopes should be limited to 60 loaded in a tray at one time. Nuvera feeder trays feed until almost
empty but not until empty, leaving 20~40 sheets remaining. When running envelopes frequent
reloading of the feeder trays will be required.
Very slight wrinkles (1/2 inch long) may occur on the trail edge of envelopes at the corners.
Due to the nature of feeding envelopes with flap open, some mis-stacking may occur in the top tray
as the envelopes catch on the open flaps.
Envelopes can only be sent to the Top Tray.
• DocuCards
DocuCards can only be loaded 100 at a time in a tray. Nuvera feeder trays feed until almost empty
but not until empty, leaving 20~40 sheets remaining. When running DocuCards, frequent reloading
of the feeder trays will be required.
DocuCards can only be run to the Top Tray of the finisher. Some mis-stacking may occur as the
DocuCards catch on the edges of the stacked sheets.
When using DocuCards, it is recommended that you use a Tiltatron (available from CAS).
DocuCards are not supported on the Nuvera MX system.
FreeFlow™DocuSP®
• The Token Ring option is no longer natively supported by DocuSP®. Customers requiring Token
Ring connectivity should acquire a Token Ring to Ethernet bridge for their system.
• The PCI Ultra SCSI SE Host Adaptor kit for the QIC and 4mm tape drives used with previous Xerox
Production Systems including the Xerox Nuvera™ 100 and 120 does not work with the Next
Generation FreeFlow™ DocuSP
®
Controller now introduced in all Xerox Nuvera™ Production
Systems. A compatible PCI ULTRA SCSI SE Host Adaptor kit for the Next Generation FreeFlow™
DocuSP
®
Controller is available as an option.
• DFA devices do not support single page offsetting specified within the job or set. Offset at job or set
boundary is supported. Single page job or set will offset.
• There is no floppy drive on Nuvera. Resource loading may be accomplished via the LTO Tape
option, QIC tape or over the network.
• The FreeFlow Print Manager Applet (previously available via clicking on the “Job Submission Applet”
in the Web Browser) is no longer included with the system. Note that the standalone FreeFlow Print
Manger product continues to be available for purchase.
Printer Module
• This is not a print to edge system due to potential image quality defects on the edge of the page.
• Printing on SRA3 can result in inboard and outboard edge image quality defects.
• The Nuvera Digital Production System provides very good support for imaging on pre-printed
materials. However, to obtain best results, please follow the guidelines outlined here:
Design the pre-printed image so that no ink, varnish, or aqueous coating is placed in the area to
be printed on by Nuvera. Toner does not adhere as well to the stock when printing over inks or
varnish. If Nuvera must print over pre-printed ink, results are more likely to be acceptable if the
color is screened back to less than 30%, or an uncoated base stock is used.
Use a laser-compatible printing process for the pre-printed stock. Choose inks, varnishes, and
coatings that are temperature stable and have low levels of petroleum distillates. UV-cured inks
are recommended, to insure complete curing before printing on with Nuvera. Do not use
stock
on Nuvera that has been pre-printed on xerographic equipment.
Select base paper stock approved for use on Nuvera (see the Compatible Media List section).
There are other factors that should be taken into account to successfully print on pre-printed stocks.
Refer to the Xerox Nuvera™ DPS Paper Guide, available on Xerox.com, for additional
considerations and performance expectations.
