Dil ID: 14
Dil Adı: sloavakia
Dil Kodu: sk9tayfun Produkty značky Shure
Dünyanın En Büyük
Elektronik Bilgi Kütüphanesi



Maximum Output Noise
(HI IMPEDANCE MIC. OUT-
PUT, in dB below
1 volt):
300-20.000
Hz
30-20,000
Hz
(Noise)
(Hum
and
Noise)
Lo Imp. lnput
150 ohm Termination -103 dB -95 dB
Hi Imp. lnput
33
kilohm Termination -104 dB -95 dB
Distortion
(any level of regulation):
3%
maximum THD
Dynamic Characteristics:
Fast attack, moderate re-
covery, fixed.
Attack: For a 20 dB step increase above thres-
hold, gain is within 2 dB of final value in
500 microseconds.
Recovery: For a 20 dB step decrease to thres-
hold, gain is within 2 dB of final value
in 700 milliseconds.
Battery Life:
Approximately 200 hours
Dimensions:
See Figure
5.
Net Weight:
1
kg (2.2 Ib)
3
-90 -80 -70 -60 -50 -40 -30 -20 -10 0
HI
IMP
I
MIC.
INPUT VOLTAGE
(DBV)
DBV
-
VOLTS
RM5
RE I V
STATIC INPUT-OUTPUT CHARACTERISTICS
(INPUT LEVEL CONTROL
MAXIMUH)
FIGURE
1
lnput Connections:
The receptacle marked MIC. INPUT
is designed for either low (25- to 600-ohms)
-
or high-
impedance (50,000-ohms) inputs. The impedance is
selected by a slide switch above the input receptacle.
The unit is not recommended for use with crystal or
ceramic microphones.
The input receptacle is a professional three-pin
female audio connector.? See Figure 2A for low- and
high-impedance connections to receptacle.
.
.-
-
-
--
-.
-..
INPUT INPUT
LOW IMPEDANCE
(BALANCED
LINE)
HIGH
IMPEDANCE
INPUT
PLUG
CONNECTIONS
FIGURE 2A
Output Connections:
The receptacle marked MIC.
OUTPUT is a dual-impedance output selected by the
switch above the receptacle. This output is designed
to work into a 25- to 600-ohm microphone line or
microphone input, or into
a
high-impedance amplifier
or tape recorder microphone input. The receptacle
is a professional three-pin male audio connector.? See
Figure 2B for microphone level output receptacle con-
nections.
SHIELD
.
-. .
- -
-
-
,T
18
I /
j
-.........
A,,
MIC.
OUTPUT
MIC
OUTPUT
HIGH
IMPEDANCE
LOW
IMPEDkNCE
IBALANCEO
LINE)
MICROPHONE
OUTPUT
PLUG
CONNECTIONS
FIGURE 28
The receptacle marked AUX. OUTPUT is a phono
pin jack which accepts a standard phono pin plug.
This output is designed to work into a high-impedance
(10 kilohms or greater), high-level input of a mixer,
preamplifier, amplifier, or tape recorder. This output
may be connected to the AUX. INPUT of an M68 Series
Mixer, the HIGH-LEVEL INPUT of an M63 Audio Master
or the
LINE INPUT (bridging) of an M67 Professional
Microphone Mixer.
The static characteristics of the high-level AUX.
OUTPUT are shown in Figure
IB. This output provides
a constant
1 volt level (with a 47-kilohm load) when-
ever the input level is above threshold. Below thres-
hold it provides approximately 60 dB of gain over the
HI-IMP MIC. input.
NOTE: This output is disabled when the MASTER
CONTROL switch is set to "Bypass."
Battery and Auxiliary Power Connections:
The battery to power the M62V is shipped with the
unit but must be installed. Install as follows:
1. Remove Battery Compartment cover by removing
the lower slotted screw holding cover, loosening
the upper screw, and sliding the cover down.
2. Snap battery into clips provided.
3.
Replace Battery Compartment cover and tighten
screws securely.
Battery Replacement-Use
Eveready type 216 or 222,
or equivalent
9V Battery.
AUX. INPUT POWER:
This jack is used as a power
input when using the power supply of a Shure M67 or
M68 Series Mixer or M63 Audio Master. In this
case, the battery should be disconnected.
A special
connecting cable is provided to connect the AUX.
INPUT POWER jack on the
M62V to the ACCESSORY
28 V. D.C. jack on the M68 Mixer or to the POS. (red)
30 V. D.C. jack on the M67 Mixer or M63 Audio Master.
In order to utilize ac current, the use of a 9 volt
D.C. Battery Eliminator is suggested. There is a pro-
vision in the battery compartment cover that will allow
using a
9
Vdc Battery Eliminator to power the M62V.
The Battery Eliminator cable is to be slipped into the
split rubber grommet on the cover of the battery com-
partment. To secure cable, rotate grommet
Y2
turn.
Connection is to be made using the same battery
clips that normally connect to the 9 volt battery.
Designed to mate with Cannon
XL
series, Switchcraft
A3
(Q.G.)
series or equivalent connector.
[Shure part
95,4407
(Note:
If
a
Shure
M683
M67
Or
M63r
Or
a
Battery
(male)
or
95A548
(female)].
Eliminator is to be used, first remove the battery.)
Page
2