Station info
Status Reporting in Station mode
DHCP Client in Station mode
Detailed information can be retrieved while selecting the particular MAC of
the associated station:
Device Name :displays the client’s host name associated to the
respective AP. The device name could be change on the System Page.
Connection time value represents the running total of time the station
is associated. The time is expressed in days, hours, minutes and
seconds;
Signal Strength value represents, in dBm, the last received wireless
signal level;
Noise Floor: displays the current value of the noise
(http://en.wikipedia.org/wiki/Electronic_noise) level in dBm. Noise Floor
(http://en.wikipedia.org/wiki/Noise_floor) is taken into account while
evaluating the signal quality (Signal-to-Noise Ratio SNR, RSSI) while
value mean depends on signal strength above the noise floor.
ACK/Distance: these values indicate the ACK Timeout and its
corresponding distance to the station.
CCQ value represents the quality of the connection to the Station;
Last IP: displays the last station’s IP address associated to the AP.
Tx/Rx Rate represents the data rates, in Mbps, of the last transmitted and received packets;
Tx/Rx Packets value represents the total amount of packets transmitted to and received from the Station during the connection
uptime;
Tx/Rx Packet Rate, pps represents the mean value of the transmitted and received packet rate;
Bytes transmitted value represents the total amount of data (in bytes) transmitted during the connection;
Bytes received value represents the total amount of data (in bytes) received during the connection;
Negotiated Rate/Last Signal (dBm) table values represent the received wireless signal level along with the all data rates of
recently received packets. "N/A" value is represented as the Last Signal if no packets were received on that particular data rate.
The information in the statistic window is updated automatically. The information in the station statistics window can be updated
using the Refresh button. Window can be closed with the Close this window button.
AP Information: selection opens the connection statistics window while
operating in Station mode.
The following link statistics is provided:
Access Point shows MAC address of the Access Point station is associated
to;
Device Name: displays the host name of the Access Point the station is
associated to.
Connection time value represents the running total of time the station is
associated to the AP. The time is expressed in days, hours, minutes and
seconds;
Signal Strength value represents the last received wireless signal level;
Noise Floor: displays the current value of the noise (http://en.wikipedia.org
/wiki/Electronic_noise) level in dBm. Noise Floor (http://en.wikipedia.org
/wiki/Noise_floor) is taken into account while evaluating the signal quality
(Signal-to-Noise Ratio SNR, RSSI) while value mean depends on signal
strength above the noise floor.
ACK/Distance: these values indicate the ACK Timeout and its
corresponding distance to the AP.
CCQ value represents the quality of the connection to the AP;
Tx/Rx Rate represents the data rates of the last transmitted and received
packets;
Tx/Rx Packets value represents the total amount of packets transmitted and received during the connection;
Tx/Rx Packet Rate (packets per second) represents the mean value of the transmitted and received packet rate;
Bytes transmitted/received value represents the total amount of data (in bytes) transmitted and received during the connection;
Negotiated Rate/Last Signal (dBm) table values represent the received wireless signal level along with the all data rates of
recently received packets. "N/A" value is represented as the Last Signal if no packets were received on that particular data rate.
To reconnect to the AP press the Reconnect button, in order to reestablish the wireless link
The list can be updated using the Refresh button.
DHCP Client: (Applicable for Router - DHCP mode only) shows the device’s WAN
IP address, Netmask, DNS servers and Gateway while operating in DHCP Router
mode.
IP Address: displays the device’s WAN IP address while operating in DHCP -
Station mode.
Netmask:displays the device’s netmask when operating in DHCP Client
mode. It is assigned automatically by the DHCP server (not the device’s
DHCP server), which assigns the WAN IP address to the device.
AirOS 5.3 - Ubiquiti Wiki
http://www.ubnt.com/wiki/AirOS_5.3
8 van 34 14-4-2011 21:46
