INITIAL PAIRING TO THE VOICE PROMPTS:
1. READY (POWER ON)
2. SEARCHING PHONES (FOR PREVIOUS PAIRED PHONES)
3. PLEASE SEARCH AND SELECT THE “BEEBT-22” DEVICE FROM
MOBILE PHONE AND ENTER “0000”.
4. YOU ARE NOW READY TO USE THE HF SYSTEM.
Note: The Bluetooth interface will remember upto the last 8 devices.
Note: If pairing is unsuccessful after several attempts power o then
power back on to re-attempt, if unsuccessful please contact our tech
support line.
AUTO RE-CONNECT:
1. The BEEBT-22 module will automatically re-connect the a previously
paired mobile phone when the ignition is turned “ON” to the vehicle
and the mobile phone’s Bluetooth feature is also on.
Note: The bluetooth module will re-connect with the last mobile phone’s
it was paired with. If no mobile phone is not found, it will
revert to the pairing process.
BLUETOOTH INTERFACE FOR SELECT 1998-2011 TOYOTA & SCION VEHICLES
TOYOTA
2003 - 2011 4 Runner
2000 - 2009 Avalon
2002 - 2011 Camry
1998 - 2011 Corolla
2000 - 2005 Celica
2000 - 2005 Echo
2001 - 2011 Highlander
1998 - 2011 Land Cruiser
2007 - 2011 FJ Cruiser
2002 - 2010 Matrix
2001 - 2005 MR2
2004 - 2011 Prius
2001 - 2005 RAV4
2001 - 2011 Sequia
1998 - 2011 Sienna
1998 - 2011 Solara
2000 - 2011 Tacoma
2000 - 2011 Tundra
2009 - 2011 Venza
2007 - 2011 Yaris
SCION
2004 - 2011 xA
2004 - 2011 xB
2004 - 2011 tC
2004 - 2010 xD
IMPORTANT NOTE
FOR CARS 1998-2003, WITH BASE
RADIO. VEHICLE MUST HAVE ONE OF
THE FOLLOWING FOR KIT TO
FUNCTION:
1. STEERING WHEEL CONTROLS
2. AVC CONNECTOR (XM PORT)
3. CD CHANGER PORT.
We recommend reading this installation guide rst before starting any
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We oer telephone support M-F
9:00 AM – 5:00PM PDT toll free at 1 (855) 822-1348. We are here to
help.
PRELIMINARY:
- Disconnect the positive(+) battery cable for radios that are
non-navigation. Radios that are navigation ready should not
disconnect the battery cable. Please use caution when installing.
Do not install the interface near or on the vehicle’s HVAC system.
This will prevent overheating and condensation build up.
- Determine the proper installation method for your specic vehicle.
Use overview to help you determine installation method.
INSTALLATION
1. Remove the factory radio to gain access to the factory radio wiring
connectors.
2. Disconnect the factory connectors from the rear of the factory radio.
3. Connect the male connectors of the interface power harness into the
factory radio.
4. Reconnect the factory connectors into the mating connectors of the
interface.
5. Connect the male 3-pin connector the pigtail connector.
6. Route the microphone to a desired location, (for example above the
rear view miror).
7. Re-install a factory radio back into the vehicle’s dash.
VOICE DIAL PRESS PWR BUTTON TWICE
ANSWER PRESS PWR BUTTON ONCE
END A CALL PRESS PWR BUTTON TWICE
REJECT PRESS PWR BUTTON TWICE
ANSWER SECOND CALL PRESS PWR BUTTON ONCE
SWITCH BETWEEN CALLS PRESS PWR BUTTON ONCE
ENTER PRIVACY MODE PRESS PWR BUTTON ONCE
INCREASE VOLUME PRESS VOLUME UP ONCE
DECREASE VOLUME PRESS VOLUME DN ONCE
USING THE RADIO BUTTONS
Note: If after a command the radio is powered “OFF”, you must power
“ON” the radio to regain volume control.
Note: If an incoming call is answered from the mobile phone’s keypad,
the call will direct itself to the headset on the mobile phone. To re-direct
the phone call to the “BEEBT-22”, it must be done directly from the
mobile phone.
Note: When transferring a phone call to the mobile phone for privacy,
the user must re-connect the
BEEBT-22 and the mobile phone by selecting the module from the
device menu on the phone.
Note: If after ending a call the radio is powered “OFF”, you must power
“ON” the radio to regain volume control.
All features of this module may vary by mobile phone
manufacturer. For questions on your mobile phone’s features,
please reference the mobile phone’s user manual for
information.
Note: On some older radios, the volume knob works in
reverse. (Eample: To lower the volume, turm the volume
knob clock-wise, and vise versa).
Note: The volume may vary at times. In order to correct the
volume level, you must set the volume knob to 0, then adjust
the volume level to your desired volume level.
PWR VOL
123
4
56
TA
AF
PTY
SEEK
TRACK
TEXT
AM FM DISC
TUNE FILE
PUSH AUDIO CTRL
OPERATING THE HANDS-FREE FEATURES ON THE RADIO
TOYOTA STANDARD AUDIO PN: 1002507A
TOYOTA PREMEIUM/JBL AUDIO PN: 1002508B
ANSWER/END
BEEBT-22
SCAN TUNE
PWR VOL
AUTO P
SEEK
TRACK
RPT
RPT
RANDDISC
SKIP
AM
FM
TAPE
DISC
CONTROL
MODE
123456
AUDIO
PUSH
ANSWER/END
12-PIN
(male plug)
12-PIN
(female plug)
INTERNATIONAL ADAPTOR PN: CJA25096
24-PIN
(male plug)
12-PIN
(male plug)
TO FACTORY
RADIO
10-PIN
(male plug)
6-PIN
(male plug)
12-PIN
(male plug)
20-PIN
(male plug)
10-PIN
(male plug)
6-PIN
(male plug)
12-PIN
(male plug)
20-PIN
(male plug)
TO FACTORY
HARNESS
3-PIN
(male plug)
MIC
(male plug)
24-PIN
(male plug)
12-PIN
(male plug)
3-PIN
(male plug)
RADIO
12-PIN
(male plug)
20-PIN
(male plug)
12-PIN
(male plug)
20-PIN
(male plug)
HARNESS
INTERNATIONAL ADAPTOR PN: 1002504
12-PIN
(male plug)
12-PIN
(female plug)
PWR
AUDIO CONT MUTESCAN TEXT1 2 3 4 5 6
VOL
SELECT
FM
1/2
AM
SAT
DISC
SSP
AUX
iPod
ANSWER/END
SCAN TUNE
PWR VOL
AUTO P
SEEK
TRACK
RPT
RPT
RANDDISC
SKIP
AM
FM
TAPE
DISC
CONTROL
MODE
123456
AUDIO
PUSH
INTERNATIONAL HARNESSES NOT INCLUDED.
SPECIAL ORDER ONLY.
JBL
TOYOTA
ANSWER/END
Rev. 082614
