6
D
1509)50-4
Installation
It is strongly recommended
to use a new hose to
connect the dishwasher to
the water supply line, and the
old hose-set should not be
reused. Asking to specilized
shop or an authorized
service technician (see
Service).
Condensation-proof tape
On some models, a
transparent condensation-
proof adhesive tape has been
provided.
It should be stuck onto the
lower side of your wooden
worktop to protect it from the
formation of condensation.
When not provided, this tape
can be requested as a spare
part from authorised
retailers.
Choose where you want to
install your dishwasher, you
can place it so that its sides
or back panel are side by
side with furniture or up
against the wall. (See the
built-in instructions for the
measures). The dishwasher
is provided with water supply
and drain hoses, which can
be directed towards the left
or right to facilitate
appropriate installation.
Levelling
Once the appliance is
positioned, adjust the feet by
screwing them in or out
depending on how high you
want it and to level it so that
it is horizontal. Make sure
that it is not inclined more
than 2 degrees. If the
appliance is level, it will help
ensure its correct operation.
Height Adjustment
Insert the appliance into the
cutout and then adjust the
height using the screws
located on the front bottom
part of the machine. Use a
screwdriver to turn the
screws in the clockwise or
anti-clockwise direction to
increase or decrease the
height respectively.
Cold water connection
Connect the cold water
supply hose, and making
sure that it is fastened tightly
in place. If the water hoses
are new or have been out of
use for an extended period
of time, let the water run to
make sure it is clear and free
of impurities before making
the connection. If this
precaution is not taken, the
water inlet could get blocked,
causing damage to your
dishwasher.
Drain hose connection
WARNING: Connect your
dishwasher drain hose to
pipes which connect to the
foul drain system and not to
surface water drains.
IMPORTANT: For the
correct operation of your
dishwasher, it is essential to
comply with the following
information:-
Standpipe:
Ensure that the hose is not
pushed too far down the
standpipe.
If the end of your drain hose
is fitted with ‘retaining flaps’,
ensure they are inserted fully
into the standpipe. This will
prevent the pipe from
jumping out during
installation and use.
DO NOT
position the
standpipe near
an electrical
outlet.
ENSURE that
the drain hose is not kinked
and it is routed as shown in
the diagram.
The standpipe should have
a bore of at least 38mm (11/
2”). It should be installed as
shown, have a trap fitted and
must discharge into the
same drain system as your
household sink.
It MUST NOT be connected
to a surface water drain.
Sink Waste System:
For under sink drainage:
Before connecting the drain
hose, remove any internal
restrictions - This will
prevent a build up of debris
which could cause a
blockage.
Remove any restrictions
from the waste spigot and
ensure that the sealing bung
is removed. The hose should
be routed, such that it is
raised to a minimum height
of 800mm (31/2”).
NOTE: Ensure the sink
outlet pipe has a minimum
diamtere of 32mm.
1. Untie the end of the GREY
drainage hose from the rear
of the appliance.
2. Reposition the ‘Hooked
End Support’ as required
along the GREY drainage
hose.
3. If fitting an under sink
waste disposal unit, cut out
the membrane, bung or
blanking plug.
Ensure the drain hose is
securely attached, to prevent
it coming away while the
machine is in use and
causing a flood.
Anti-flooding protection
To ensure floods do not
occur, the dishwasher:
- is provided with a special
system which blocks the
water supply in the event of
anomalies or leaks from
inside the appliance.
- is provided with a Water
Stop safety device, in other
words it has a water inlet
hose that consists of a
transparent hose on the
outside and a red hose on
the inside: both the hoses
can withstand extremely high
pressure. If the internal hose
breaks, the external hose
becomes a bright red colour
and carries the water instead,
thus avoiding any leakage.
It is very important to check
the external hose regularly:
if it is a bright red colour, it
must be replaced by an
authorised technician as
soon as possible (see
Assistance).
WARNING:
HAZARDOUS
VOLTAGE!
Under no circumstance
should the water inlet hose
be cut as it contains live
electrical parts.
