Dil ID: 7
Dil Adı: french
Dil Kodu: fr1tayfun Produits de la Marque Asko
Dünyanın En Büyük
Elektronik Bilgi Kütüphanesi



Page 12
Model 1895 was designed to easily accommodate
custom panels. If you use the 4” toe kick, a 2” filler strip
or a pullout cutting board above the unit will be
necessary.
The opening width for Model 1895 is 23-5/8” (600 mm),
which is 3/8” narrower than standard domestic
dishwashers.
ITEMS PRITEMS PR
ITEMS PRITEMS PR
ITEMS PR
OO
OO
O
VIDED VIDED
VIDED VIDED
VIDED
WITH WITH
WITH WITH
WITH
THE UNITTHE UNIT
THE UNITTHE UNIT
THE UNIT
Two short screws (D)
Four long screws (E)
Four adhesive-backed plastic spacer washers (D)
One protective tape
ADJUSTING THE DOOR SPRINGSADJUSTING THE DOOR SPRINGS
ADJUSTING THE DOOR SPRINGSADJUSTING THE DOOR SPRINGS
ADJUSTING THE DOOR SPRINGS
After you install the custom
panel, make sure the door can
be opened at any angle. If it
tends to fall down, pull out the
machine and tension the door
springs on the sides of the
machine by moving them one
hole farther back or by twisting
the spring to make it shorter. If
that doesn’t resolve the problem, you may need to
purchase the heavy-duty door springs (Part Number
8071323-77).
FASTENING THE DISHWASHERFASTENING THE DISHWASHER
FASTENING THE DISHWASHERFASTENING THE DISHWASHER
FASTENING THE DISHWASHER
TO THE CABINETTO THE CABINET
TO THE CABINETTO THE CABINET
TO THE CABINET
Refer to page 8.
WARNING!
The custom panel must not
obstruct the turbo fan exhaust.
See step 2 above for instructions
on how to adjust the fan exhaust.
Installing the 1895 Custom Panel
WW
WW
W
OODEN POODEN P
OODEN POODEN P
OODEN P
ANEL DIMENSIONSANEL DIMENSIONS
ANEL DIMENSIONSANEL DIMENSIONS
ANEL DIMENSIONS
Width: 23-3/8” (594 mm)
Height: 22-9/16”–24” (573 mm–609 mm)
Thickness: 3/4” (19 mm) (to be flush with the control
panel)
Weight: Up to 22 lbs.
NOTE:
Specifications subject to change without
notice.
NOTE:
Heavy-duty door springs can be purchased for
wooden door panels weighing over twelve
pounds. (P/N 8071323-77).
INSTINST
INSTINST
INST
ALLING ALLING
ALLING ALLING
ALLING
THE PTHE P
THE PTHE P
THE P
ANELANEL
ANELANEL
ANEL
Before fitting the custom panel, the dishwasher must
be installed underneath the cabinet. After you’ve made
the required measurements, pull the machine out again
to install the panel.
Refer to the illustration at right for instruction references.
1. Loosen the screws (A) on the outer edges of the
dishwasher door.
2. Pull the turbo fan exhaust frame (B) down until the
lower edge aligns with the lower edge of the cabinets
and tighten the screws (A). Next, snap the plastic
duct securely into the turbo fan exhaust vent.
3. The spacers (C) between the control panel and the
custom door panel allow you to accommodate the height
of the custom panel (from 1” up to 1-7/16”). To remove a
spacer, loosen the nuts at the bottom of the spacers
and remove as many as necessary. Screw the nuts
back on and cut off any protruding parts of the plastic
screws. (If necessary, you can omit the spacers.)
4. To mark where to put the two short screws (E), hold
the custom panel in place against the front of the
dishwasher door and measure 16-1/8” from the top of
the dishwasher, marking that distance on both sides
of the custom panel. Next, measure 5/8” from the edges
and mark that across the first measurement.
5. Insert the short screws (E) into the back of the
wooden panel where you marked, leaving 1/8” of
space between the screw heads and the panel.
6. Insert the screw heads (E) into the lower part of the
keyholes (D) and push the panel upward until the
door aligns with the cabinets.
7. Holding the custom panel in place, open the
dishwasher door and tighten the four screws (F)
that secure the panel.
FITTING FITTING
FITTING FITTING
FITTING
THE SEMI-INTEGRATHE SEMI-INTEGRA
THE SEMI-INTEGRATHE SEMI-INTEGRA
THE SEMI-INTEGRA
TED CUSTTED CUST
TED CUSTTED CUST
TED CUST
OM DOOROM DOOR
OM DOOROM DOOR
OM DOOR
PP
PP
P
ANEL ON MODEL 1895ANEL ON MODEL 1895
ANEL ON MODEL 1895ANEL ON MODEL 1895
ANEL ON MODEL 1895