JnstallBtion^■ - Conne0ing Optional.IceMake.r.ToWatet'Supply..,
A WARNING
To,avoid .electric shock,'which.can cause;.death or,.severe,,.personal injury, disconnect the.
T,efrigeratorfro.rn .'electrical power before ..connecting a water'S.uppfy'-lin.e.to the refrigerator. 'h
i^CAUTION To Avoid ..Property 'Damage:'
Copper,.tub.in.g .is recommend.ed for-the water'Supply.'!i|i6..'Water-supply..tubing made. of.plastic is. tiot...T
■recommended since.jt greatly increases.the potential for water leaks.'Manufacturer will not be responsible
for-any damage'if.plastic tybing is used fo.r-supply-'¡ine..'■■■■■ .'■ ■ ■■. ■.'■■■'■■ ■'■■"■.:'■ ■■■■.■.. ■■ ■■
.DQ..NOT install w.ater.sijpply tubing in, areas. whe.re temperatures .fall..below freezing. ■■ " ■' :.. ■■■■■■■■ ■■.":
Chem.icals from .a ma|funct.ioni,iig softener can.darn.a.ge the ice maker. If the ice maker.is.connected to soft
water, ensure that the soft,en.er.is.maintain.ed,an.d .working properly. ■.. ■■.....■. ■ ■■'■■■ ■ '.■■ .■ ■ ■ .". ■■■" - ■ .■.. ■ ■ ■' .:
.■|MTORTANT:'Ensure ;that your water supply line connections comply with all local plumbing codes. ■■ '■
Before Installing The Water Supply Line, You Will Need
• Basic Tools: adjustable wrench, flat-blade screwdriver, and Phillips'’'“ screwdriver
* Access to a household cold water line with water pressure between 20 and 120 psi.
• A water supply line made of Va inch {6.4 mm) OD, copper tubing or braided water line. To determine the length of
copper tubing needed, you will need to measure the distance from the ice maker inlet valve at the back of the
refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out
for cleaning (as shown).
® A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type
shutoff valve.
* A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.
■'NOTE: A water fine kit is available.through.Sears retail.or catalog stores at .additional.cost.'.
To Connect Water Supply Line To Ice Maker Inlet Valve
1.
2.
3.
4.
5.
6.
8.
9.
10.
Disconnect refrigerator from electric power source.
Place end of water supply line into sink or bucket Turn ON water supply
and flush supply line until water is clear. Turn OFF water supply at shut
off valve.
Unscrew plastic cap from water valve inlet and discard cap.
Slide brass compression nut, then ferrule (sleeve) onto water supply line,
as shown.
Push water supply line into water valve inlet as far as it will go (14 inch).
Slide ferrule (sleeve) into valve inlet and finger tighten compression nut
onto valve. Tighten another half turn with a wrench; DO NOT over tighten.
With steel clamp and screw, secure water supply line to rear panel of
refrigerator as shown.
Coil excess water supply line (about 214? turns) behind refrigerator as shown
and arrange coils so they do not vibrate or wear against any other surface.
Turn ON water supply at shutoff valve and tighten any connections that
leak.
Reconnect refrigerator to electrical power source.
To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/
OFF position of arm).
Plastic Water •
Tubing to Ice Maker
Valve Inlet
•Water Valve,
-Copper water line ... .. ..'
from household water supply
• {Include enough tubing in loop to allow
moving refrigerator out.tor cleaning.)
IMPORTANT:'.It takes approximately'24..hours-for the .ice maker to begin producing ice. Air in, new .plumbing lines 'may.i
cause ice maker, to cycle two or th.ree.times before making .a full tray of ice. New plumbing may cause ice to be discolored
■"or'have poor flavor. Discard .ice made during the first 24.hours.
m-.
m:.
m
