Productos de la Marca Asko

WASH PROGRAM ACTIONWASH PROGRAM ACTION

WASH PROGRAM ACTION

The paragraphs below explain the motor operations

for the various wash programs.

PresoakPresoak

Presoak

No tub action while filling. After filling, clockwise

3 seconds on, 27 seconds off, counterclockwise 3

seconds on, 27 seconds off. Then 10 minutes of no

tub action.

PrewashPrewash

Prewash

Clockwise 9 seconds on, 6 seconds off,

counterclockwise 9 seconds on, 6 seconds off, and

so on.

Normal washNormal wash

Normal wash

Clockwise 12 seconds on, 3 seconds off,

counterclockwise 12 seconds on, 3 seconds off, and

so on.

Synthetic washSynthetic wash

Synthetic wash

Clockwise 3 seconds on, 27 seconds off,

counterclockwise 3 seconds on, 27 seconds off, and

so on.

ool/Hand washool/Hand wash

ool/Hand wash

Clockwise 3 seconds on, 57 seconds off,

counterclockwise 3 seconds on, 57 seconds off, and

so on.

Fluff (at end of program)Fluff (at end of program)

Fluff (at end of program)

Clockwise 12 seconds on, 3 seconds off,

counterclockwise 12 seconds on, 3 seconds off, and

so on.

ashing cycleashing cycle

ashing cycle

40 ± 1 rpm Presoak, prewash.

49 ± 1 rpm Main wash, rinses.

SPIN SPEEDSSPIN SPEEDS

SPIN SPEEDS

W600: 800 or 1000 rpm

W620: 600–1200 rpm *

W640: 600–1400 rpm *

W660: 600–1600 rpm *

* Selectable in 100 rpm steps.

OUTOUT

OUT

OF-BALANCE CHECKOF-BALANCE CHECK

OF-BALANCE CHECK

There are two spin sequences, long and short. Both consist

of a preliminary spin, the washing cycle and a main spin.

Before the preliminary spin, the machine runs a

separating cycle at 100 rpm and measures the drum

speed on the way up and down. This checks for

out-of-balance. During this cycle the tub may make

violent movements although there is nothing

wrong.

There are three different limit values for out-of-

balance that permit different spin drying speeds.

Limit value 1: 1300 – 1600 rpm

Limit value 2: 1000 – 1299 rpm

Limit value 3: – 999 rpm

Preliminary spin (long and short)Preliminary spin (long and short)

Preliminary spin (long and short)

A preliminary spin dry is performed so that the

machine will have a smoother start for its main spin

dry cycle. It does this by removing over half the

weight in water by spinning at 900 rpm for

approximately one to two seconds.

A maximum of ten restarts are made at limit value

3 to reach 500 rpm. If the out-of-balance is still too

great in the final (tenth) attempt, the program will

continue without the preliminary spin or main spin

dry cycles. This is indicated on the display after the

program has finished.

Selected spin speed 1300–1600 (long andSelected spin speed 1300–1600 (long and

Selected spin speed 1300–1600 (long and

short)short)

short)

A maximum of five restarts at limit value 1 are made

to try to achieve the selected spin drying speed.

If the out-of-balance is too great, a maximum of three

restarts will be made at limit value 2 to try to achieve

1200 rpm. If limit value 1 is achieved during any of

these three restarts, the selected spin speed will be run.

If the out-of-balance is still too great, a maximum

of two restarts at limit value 3 will be made to try

to reach 900 rpm. If limit value 2 or limit value 1

is achieved during either of these two restarts, 1200

rpm or the selected spin speed will be run.

If the out-of-balance is still too great in the final

(tenth) attempt, the program will continue without

spin drying. This is indicated on the display after

the program has finished.

Selected spin speed 1000–1300 rpm (longSelected spin speed 1000–1300 rpm (long

Selected spin speed 1000–1300 rpm (long

and short)and short)

and short)

A maximum of eight restarts at limit value 2 are

made to try to reach the selected spin drying speed.

If the out-of-balance is too great, a maximum of

two restarts will be made at limit value 3 to try to

achieve 900 rpm. If limit value 2 is achieved during

either of these restarts, the selected spin drying speed

will run.

MOTOR OPERATIONS