Connections & Setup
STEP 2: Conti^urtTK} for CabI«
T«eptrab|r«piir^w№}rNrt<iUibot,lMGUSCntiH«riMmMfd(t6lsww
On ttuniil )mir Tv It <n wlwi wtq th> uWi bm. tbt rnort comnorfr wfd
MjMi'diinnil b e.'PIUM tereuli )T«ur uMt pr»vklir V f«u tft mut. as an
iMomct Mkctton rmA In a M« or mif)) Rrecn iNtili watiMns TV.
Whtch channel is your TV tuned to when using
the cable box?
=-“-;az. ^
^ 03
:!'.:04 ■ . ■
V^ol/AliX
On yotfl Tv tsmciK, ttwi45i'iiiwn ro itow ansvrtr,
PiessOK to {h»s*. .
HighliiTht the chiinnel to which you have to tune your W in order to see
cable prognimmin^, and press OK (a screen appears reminding yon ttr
connect yonr G-LINK cable to ytHir TV and cable box).
Notes: Channel (')-> is the most common.
Chouse Video 1/AUX if your cable box is connected to your TV with
andio/i'kieo cables instead of a coaxial cable. Go to page'7 for pictures of
these cables.
STEP 2: Contigurtng ror Cable
Stiedirig Qk «<T*ct uHt box brand Irem'ttM kt iMlow Is necM H
MMiatkstritMbvTVprotb'ambcirV' Vyourkiiwtlawwiiwubir
tM brJivt (luM <erMA yotr cabli providff
4. Highlight yonr brand of cable irox. and press OK.
[1 your hrancl isn't listed, highlight Not Listed and pre.ss OK.
What brand of cable box Is connected to this
1V?^
Cfli youi rV riirwti.iiys tile upioowrt keys W Imd Vtui biarnt (mnet?rj[xt6
wiliappidT you nw¥< down) Pré» № tc (№)crie
STEP 2: Coniiguring tor Cable
Make sure your cable box is on.
Tune the cable box to channel 02 (use the remote control that came with
your cable box, or press the channel buttons on the cable box).
Press OK (the GUIDE Plus+ system starts testing codes).
Important Note: When code testing is in progress, don't touch your TV,
VCR, cable box or any of the remote controls for these products.
.l^^IrTable box rrow tuned to channel OS?
/Yes
5>^^e^#hts.code again
DnyetH Tv rimoti.usi Uw upfttown keyi to highlight your Ji4w?r
PiwtOK Ic trtcoie
Look at your cable box. If it is still on and changed to channel 09, the test
was successful. Highlight Yes, and press OK (STEP 3: Configuring for a VCR
appears).
It your cable box didn’t change to channel 09 or turned itself off, you have
two choices: No and Test this code again.
Test this code again: If you think the TV, the cable box, or any of the
remote controls might have been touched or bumped during the test,
highlight Test this code again and press OK (the GUIDE Plus+ system runs
the same .set of codes).
No: It you cion’t think the test was interrupted, highlight No and pre.ss OK
(GUIDE Plus+ system tests the next code).
Repeat the previous instructions until the T\^ finds the correct cable box
code. Follow the instructions on the screen.
Note: If the TV can’t find your cable box code, a troubleshooting
checklist appears. Carefully review each checklist and follow the
instructions on the screen.
Chapter 1
17
