
HOOKUP DIAGRAMS
Quick Start
1. Start with the following settings on the back of the
SRM350v2:
Turn the POWER switch off (down).
Set the CONTOUR and MIC/LINE switches out. If using
a microphone as the input to the SRM350v2, push the
MIC/LINE switch in.
WARNING: Turn the LEVEL control
down (counterclockwise) before every
use. If not, you could be in for a
startling surprise, especially if the
last time you used it was with a
microphone and now you want to
connect a line-level source.
2. Connect the output from your signal source (mixing
console, microphone, preamp, or other mic- or line-
level source) directly to the INPUT connector on the
back of the SRM350v2. This is a combination XLR and
1/4" TRS connector, and accepts balanced or
unbalanced line-level signals from mixers,
preamplifiers, CD players, tape
decks, etc., with the MIC/LINE
switch out, and accepts direct
connections from dynamic
microphones with the MIC/LINE
switch pushed in.
3. Connect the supplied AC power cord to the IEC socket
on the back of the SRM350v2. Plug the other end into an
AC outlet properly configured with the correct voltage
for your particular model.
4. Turn on your signal source. Make sure its Master
Volume control (if it has one) is turned all the
way down.
5. Turn on the SRM350v2 POWER switch.
6. Start the signal source, whether it be speaking into a
microphone or starting a CD player. Adjust any volume
controls on the signal source for normal operation.
7. Slowly turn up the LEVEL control on the back of the
SRM350v2 until the desired volume is reached (and the
LIMIT light does not come on). Always wear hearing
protectors if you are close when it is playing at high
levels.
8. If there is no sound, always turn down the SRM350v2
LEVEL control before investigating. There may be a
mixer or preamplifier mute or tape switch engaged, or a
mic switch off.
SRM350v2: STEREO OPERATION WITH A MIXER
12k/AIR100Hz
CONTOUR
(+3dB)
POWER
LIMIT
SIGNAL
LINE
MIC
LEVEL
OO
+45
+5dB
NORMAL
PARALLEL
INPUT
THRU
M
I
C
G
A
I
N
12k/AIR100Hz
CONTOUR
(+3dB)
POWER
LIMIT
SIGNAL
LINE
MIC
LEVEL
OO
+45
+5dB
NORMAL
PARALLEL
INPUT
THRU
M
I
C
G
A
I
N
Mixing Console
(Mackie Onyx 1220i shown)
From Mixer
Right Output
From Mixer
Left Output
SOLO SOLO SOLO SOLO SOLO SOLO SOLO SOLO
MUTE MUTE MUTE MUTE MUTE MUTE MUTE MUTE
MAIN MIXTALKBACK
TAPE
MAIN OUT
IN OUT
L
R
ALT 3
-
4 OUT
CTRL - RM OUT
EQ
MID
HIGH
LLL
L
RRR
R
R/4L/3
L R L R
POWER
MIC
1 2 3 4
GAIN GAIN GAIN GAIN
EQ
MID
LOW
HIGH
EQ
MID
LOW
HIGH
MID
LOW
HIGH
HIGH
LOW
EQ
AUX
2
1
PAN
1
LINE
2
LINE
4
LINE
3
LINE
GAIN GAIN GAIN GAIN
AUX MASTER
2
1
SEND
RETURN
2
1
CTRL ROOM/PHONES
SOURCE
PHONES
CONTROL
ROOM
RUDE
SOLO
L R
LOW
AUX
2
1
PAN
2 3 4 7-85-6
AUX
2
1
PAN
AUX
2
1
PAN
AUX
2
1
PAN
9-10 11-12
LINE IN 9-10 LINE IN 11-12LINE IN 7-8LINE IN 5-6
MID
HIGH
LOW
EQ
AUX
2
1
PAN
MID
HIGH
LOW
EQ
AUX
2
1
PAN
MID
HIGH
LOW
EQ
AUX
2
1
PAN
MID
1