Matrix Plus Interfaces
Americas and Asia-Pacic Headquarters California, United States Tel: +1.510.337.6600
Europe, Middle East, and Africa Headquarters Cambridge, United Kingdom Tel: +44 1223 815000
China Oce Beijing, P.R. China Tel: +86-10-65811360/65815577
© 2000 Clear-Com Intercom Systems. Matrix Plus is a Trademark of Clear-Com. #INTRFC/900
IMF-3, IMF-102, TEL-14, CCI-22, FOR-22, RLY-6,
GPI-6, IFB-104, BAL-8, PIA-32, PSU-101
IMF-3 FRAME
Plug-in Module Capacity: 11
Rear Panel Connectors:
(2) 10-pin Jones (for PSU-101 power supply)
To Matrix Frame: (22) RJ-45
(when all interface modules are installed)
Interface I/O: (22) DB9-M
(when all interface modules are installed)
Power Requirements:
200 mA from PSU-101 power supply
Size: 5.25" H x 19" W x 13.75"
(133 x 483 x 345 mm)
Weight: 10 lbs (4.5 Kg)
IMF-102 FRAME
Plug-in Module Capacity: 2
Rear Panel Connectors:
(1) 3-pin EIA (for internal power supply)
(1) 10-pin Jones
(for PSU-101 redundant power supply)
To Matrix Frame: (4) RJ-45
(when all interface modules are installed)
Interface I/O: (4) DB9-M
(when all interface modules are installed)
Power Requirements,
+9 V Analog: 200 mA (frame only)
-9 V Analog: 200 mA (frame only)
AC Requirements: 90- 250 VAC, 20 W
Size: 1.75" H x 19" W x 13.75" D
(44 x 483 x 345 mm)
Weight: 6.25 lbs (2.8 Kg)
CCI-22 2-WIRE INTERFACE (2 CH)
Frequency Response:100 Hz-15 kHz, +0/-3 dB
Impedance:>10K Ohms (bridging)
Audio Level,
Clear-Com or compatible:-15 dBv nominal
Other: -10 dBv nominal
Call Signal Level (Clear-Com or compatible
only): 4 -11 VDC
Nulling Capability,
Line Length: 0 - 4,000 feet
Line Impedance:120 - 350 Ohms
Depth of Null: >30 dB, 200 Hz - 8 kHz
Nulling Tone: Via 1/8" phone jack
Power Consumption(maximum each channel):
40 mA @ 20 - 30 VDC
(Power is supplied by external party-line)
Power Requirements:
0 mA from PSU-101 power supply
FOR-22 4-WIRE INTERFACE (2 CH)
Frequency Response:20 Hz -15 kHz, +0/-3 dB
Audio Input Level: 0 dBv nominal
Input Impedance:>10K Ohms,
transformer balanced
Audio Output Level,
Nominal: 0 dBv, -15 dBv, or -55 dBv,
jumper selectable
Maximum: +20 dBv
Output Impedance:150 Ohms nominal,
transformer balanced
Call Signal Input: 4 - 50 VDC
Relay: SPDT, 24 VDC @ 1 Amp
Power Requirements:150 mA max from
PSU-101 power supply
TEL-14 TELEPHONE INTERFACE
(2 CH) AUDIO
Frequency Response:300 Hz - 3.4 kHz
Send Gain Control Range: +/-12 dB
Receive Gain Control Range:+/-12 dB
Ring Detect Sensitivity: Operates with most
international telephone ring signal standards.
Auto-Mode Levels:-12 dBv on intercom line
for -9 dBm on telephone line; -27 dBm on
telephone line for -12 dBv on intercom line.
TELEPHONE DISCONNECT
Dial Tone: 350 Hz + 440 Hz, continuous
Busy Tone: 480 Hz + 620 Hz,
0.5 sec on / 0.5 sec o
Reorder Tone: 480 Hz + 620 Hz,
0.25 sec on / 0.25 sec o
Loop Current Interruption: >5 ms
DC Isolation: >10M Ohms between each
telephone line and the IMF interface frame.
POWER REQUIREMENTS
Supplied by the PSU-101 power supply
Voltage Required:Between +/-8 and +/-12 Volts
DC unregulated
Current Required: +370 mA /-130 mA
CONNECTORS (VIA IMF FRAME)
To Matrix Frame: (2) RJ-45
DB-9M Connector:
(2) telephone line connections
(2) for relay contacts
Relay Contacts: Type “A1”, “Dry”, normally
open when TEL-14 is on-hook
CONTROLS & INDICATORS (2 EACH)
Hook switch and LED; Send Volume control and
LED; Receive Volume control; Auto Gain switch
and LED; Auto Answer switch and LED;
Auto Nulling reset switch.
SIZE & WEIGHT
Size: 5.0625"H x 1.375"W x 9.16"D
(129 x 35 x 233 mm)
Weight: 0.78 lbs (0.32 Kg)
RLY-6 RELAY INTERFACE
Relays: Six SPDT 24 VDC @ 1 Amp
Power Requirements:150 mA max from
PSU-101 power supply
GPI-6
Input Type: Opto-isolated 4 - 30 DC or AC
Power Requirements:0 mA from PSU-101
power supply
IFB-104 IFB ROUTING PANEL
Indicators: "Power-on" LED
CONNECTORS
Program Input: (4) 3-pin XLR female
To Matrix Frame: (4) RJ-45
Talent: (4) 3-pin XLR male
DC Power: (1) 3-pin XLR male
(1) 3-pin XLR female
PROGRAM INPUT
Type: Transformer isolated
Impedance: 600 Ohms bridging
Level: 0 dBv
HEADPHONE TALENT RECEIVER
OUTPUTS
Impedance: 600K Ohms transformer balanced
Power: 1 mW into 600 Ohms
LINE INPUT
(2-PAIR TALK TO MATRIX)
Type: Transformer balanced
Impedance: 600K Ohms
Level: 0 dBv nominal
Frequen
cy Response:100 Hz-
15 kHz, +/-2 dB
SIZE & WEIGHT
Size: 1.75" H x 19" W x 2" D
(44 x 483 x 51 mm)
Weight: 1.8 lb. (.82 Kg)
BAL-8 TRANSFORMER-BALANCED
PANEL
Connectors,
Output: (8) RJ-45 (to interfaces)
Input: (8) RJ-45 (from Matrix)
Indicators: "Power-on" LED
Isolation: All balanced audio pairs (2 per port
connection) are transformer isolated
Frequency Response:100 Hz - 15 kHz
Max Level: +10 dBm
Size: 1.75" H x 19" W x 2" D
(44 x 483 x 51 mm)
Weight: 5 lb. (2.3 Kg)
PIA-32 INTERFACE ADAPTER
Connectors,
Output: (6) RJ-45 (to the Matrix Plus 3 frame)
Input: (6) DB-15F
Indicators: "Power-on" LED
Electrical Requirements:90 to 260 VAC,
50 - 60 Hz @ 12 watts (in-line power supply)
Size: 1.75" H x 19" W x 6.5" D
(44 x 483 x 165 mm)
Weight: 5 lb. (2.3 Kg)
PSU-101 POWER SUPPLY
Two 9-volt switching supplies with audible
failure alarm
Output Current: 3 Amps
Indicators: 2 power supply LEDs
Rear Panel Connectors,
Alarm Out: SPST relay @ 1 amp DC rating
Mains Connector: IEC 3-pin connector
AC Power Input,
Voltage:90 - 260 VAC
Power: 125 Volt-Amps maximum
Frequency:50 - 60 Hz
Size: 1.75" H x 19" W x 7.75" D
(44 x 483 x 197 mm)
Weight: 4.5 lbs (2 Kg)
All specications are subject to change
without notice.
S P E C I F I C AT I O N S
