4
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
DELAY
The start time of the program may be delayed for a period
of time between 1 and 12 hours.
1. Press the DELAY button: the corresponding symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of
the selected wash cycle will be increased.
2. Select the wash program and close the door: the timer
will begin counting down;
3. Once this time has elapsed, the indicator light switches
off and the wash cycle begins.
To adjust the delay time and select a shorter period of
time, cancel the execution by pressing ON/OFF button
and select a new delay period if necessary or select and
start a desired cycle directly.
The wash program will start automatically as soon as the
door is shut.
The Delay function cannot be changed once a wash
cycle has been started.
ZONE WASH 3D
Thanks to the additional 3D water jets placed on the
bottom of the cavity, ZONE WASH 3D option allows to
save energy or to increase the washing performance of
the dishwasher.
It is compatible with Normal and Intensive cycles, and it
works with one rack at once.
• ZONE WASH 3D + NORMAL CYCLE: it allows to reduce
energy consumption up to 40%.
• ZONE WASH 3D + INTENSIVE CYCLE: it increases the
washing performances up to 40%. Ideal for very soiled
mixed loads, e.g. pans and saucepans, dishes with
heavy encrustation or difficult-to-clean crockery
(grater, vegetable mill, dirty cutlery).
How to activate the option:
1. Select a compatible cycle
2.By default the appliance washes dishes in all racks. To
wash only the specific rack, press this button repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (only cutlery rack)
shown on the display (option is OFF and the appliance will
wash dishes in all racks).
Remember to load the crockery in the selected rack only.
TABLET (Tab)
This setting allows you to optimize the performance of
the program according to the type of detergent used.
Press the TABLET button (the indicator light will light up)
if you use combined detergents in tablet form (rinse aid,
salt and detergent in 1 dose).
If you use powder or liquid detergent, this option
should be off.
TURBO
This option can be used to reduce the duration of the
main programs while maintaining the same washing and
drying performance levels.
After selecting the program, press the TURBO button and
the indicator light will switch on. To deselect the option,
press the same button again.
ACTIVE OXYGEN (O3)
This device releases ozone molecules into the
dishwasher, i.e. a natural substance that reduces
unpleasant odours.
It should be used between two different wash cycles and
ONLY after soiled crockery has been loaded.
To start the ACTIVE OXYGEN option press and hold for 3
seconds the button O3 and close the door.
The option will stay active either for 24 hours or until the
wash cycle is started. More items can be introduced at
any time until full load. The typical faint odour that can
be smelt inside the dishwasher - the same as you
sometimes get with storms - is due to the ozone
produced by lightning discharges. This is normal. The
device produces just a small quantity, which soon decays.
OPERATION INDICATOR
A LED light projected on the floor indicates that the
dishwasher is working. One of the following operating
modes can be selected:
aDisabled function.
b When the cycle starts the light goes on for few seconds,
stays off during the cycle and flashes at the end of the
cycle .
c The light stays on during the cycle and flashes at the
end of the cycle (default mode).
If the delayed start was set, the light goes on either for the
first few seconds or the entire duration of the
countdown, based on whether mode b) or c) was set.
The light goes off every time the door is opened. To select
the mode you prefer, switch on the machine, hold down
button P until one of the three letters appears on the
display, press button P until you reach the desired letter
(or mode), hold down button P to confirm the selection.
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times and beeps
will sound. The option will not be enabled.
