
D
1509)50-4
5
Installation
Choose where you want to
install your dishwasher, you
can place it so that its sides or
back panel are side by side
with furniture or up against the
wall. The dishwasher is
provided with water supply
and drain hoses, which can
be directed towards the left or
right to facilitate appropriate
installation.
Levelling.
Once the appliance is
positioned, adjust the feet by
screwing them in or out
depending on how high you
want it and to level it so that it
is horizontal. Make sure that it
is not inclined more than 2
degrees. If the appliance is
level, it will help ensure its
correct operation.
Cold water connection.
Connect the cold water supply
hose, and making sure that it
is fastened tightly in place . If
the water hoses are new or
have been out of use for an
extended period of time, let the
water run to make sure it is
clear and free of impurities
before making the connection.
If this precaution is not taken,
the water inlet could get
blocked, causing damage to
your dishwasher.
Standpipe:
Ensure that the hose is not
pushed too far down the
standpipe.
If the end of your drain hose is
fitted with ‘retaining flaps’,
ensure they are inserted fully
into the standpipe. This will
prevent the pipe from jumping
out during installation and use.
DO NOT position the
standpipe near an electrical
outlet.
ENSURE that the drain hose
is not kinked and it is routed
as shown in the diagram.
The standpipe should have a
bore of at least 38mm (11/2”).
It should be installed as
shown, have a trap fitted and
must discharge into the same
drain system as your
household sink.
It MUST NOT be connected to
a surface water drain.
Sink Waste System:
For under sink drainage:
Before connecting the drain
hose, remove any internal
restrictions - This will prevent
a build up of debris which
could cause a blockage.
Remove any restrictions from
the waste spigot and ensure
that the sealing bung is
removed. The hose should be
routed, such that it is raised to
a minimum height of 800mm
(31/2”).
NOTE: Ensure the sink outlet
pipe has a minimum
diamtere of 32mm.
1. Untie the end of the GREY
drainage hose from the rear
of the appliance.
2. Reposition the ‘Hooked
End Support’ as required
along the GREY drainage
hose.
3. If fitting an under sink
waste disposal unit, cut out
the membrane, bung or
blanking plug.
Ensure the drain hose is
securely attached, to
prevent it coming away
while the machine is in
use and causing a flood.
Connect to the Water
Supply...
- For your dishwasher to ope-
rate correctly it requires water
pressures in the range of 6-
150 psi (100-1000KPa). Most
cold water supplies will be in
this range. NOTE: low water
pressure will lead to
excessively long fill times or no
fill.
- Ensure that the new hose
supplied is connected and the
old hose is disposed of safely.
- Ensure the fill hose is only
fitted to the cold water supply.
DO NOT overtighten the hose
connector, hand tight is
sufficient.
- Ensure the fill hose is not
kinked.
- Tap connections (if
applicable): A range of
adaptors are available to suit
your tap.
- DO NOT connect the
dishwasher to a single outlet
instantaneous water heater or
an electric heater.
- The appliance must be
connected to the water supply
network using new hoses.
Do not use old hoses.
Drain hose connection.
WARNING: Connect your
dishwasher drain hose to
pipes which connect to the foul
drain system and not to
surface water drains.
IMPORTANT: For the correct
operation of your dishwasher,
it is essential to comply with
the following information:
Remember you will be charges for a service call is a
problem with your appliance is caused by incorrect
installation or misuse.