Продукция бренда Dacor

Preparing the Location

WARNING

Follow all cabinet dimensions shown to insure safe

operation. All minimum product dimensions must

be met or exceeded (see page 3). Dimensions

shown provide the required clearances.

• The cabinet must enclose the dishwasher on the

top, back and both sides.

• Carefully check the location where the

dishwasher is to be installed. Put it in a location

with convenient access, close to the kitchen

sink for easy water supply and drain connection.

The power supply shall meet the Electrical

Specifications on page 4. Also, the electrical

outlet or junction box shall be installed close by

in a cabinet adjacent to the location selected so

that the power cable can be disconnected without

removing the appliance from the cutout.

• The electrical wiring, water supply and drain

lines must enter through the area indicated by

the shading on the illustration at right. Preferably,

they should come through the right side of the

cabinet.

• The access hole(s) in the cabinet for the power

cordandwaterlineshallbenobiggerthan1-1/2˝

(3.8 cm) in diameter. The access hole for the

drainhoseshallbenobiggerthan2˝(5.0cm)

in diameter. The access holes for all three must

be round and smooth. If the partition is metal, it

needs to be covered with an edge protector. Call

Dacor for the part number of an approved edge

protector.

• The opening through the partition between the

drain connection and the dishwasher cutout

must be higher than the disposer or waste tee

connection (see page 6) and lower than 35”

(88.9 cm).

• Plan the installation so that the appliance can be

removed easily if service is required.

• The floor must be solid, level and all cutout

surfaces must be at right angles. In the interest

of safety, the surrounding cabinet must have

sufficient material for attachment of the anti-tip

brackets (see page

15).

• If the dishwasher is

installed in a corner,

allow a minimum

clearance of 2” (5.1

cm) from the side wall

so the door can open.

Dishwasher Cutout - Front View

Preparing for Installation

Cutout tolerances: +1/16” (+1.6 mm), -0

Model (E) (F)

RDW24I*

23 5/8” (60.0 cm)

to 24” (61.0 cm)

33 7/8” (86.0 cm)

to 36” (91.4 cm)

RDW24S** 24” (61.0 cm)

34 3/8” (87.3 cm) to

36 1/2” (92.7 cm)

*If installing model RDWH24I in a 24” wide cutout

installation of a trim kit (Dacor PN 106925) is required

to fill the space between the edge of the cutout and

the dishwasher.

** If the height of the existing cutout is too low:

- Check to see if the cabinet face can be trimmed

at the top. In many cases, when a non-standard

size dishwasher has been installed previously,

there is enough room inside the cabinet once the

cabinet face is modified.

- The dishwasher can be shortened 1/4” (6.0

mm) by not installing the plastic feet on the unit

as shown on page 11. Extra care must be

taken if the feet are not installed. Dacor is not

responsible for floor damage during installation.

- The dishwasher can be shortened 1/4” (6.0 mm)

by removing the trim pieces that surround the

wash compartment opening. NOTE: Doing so will

create a gap of 1/4” (6.0 mm) on the right and

left side of the door.

24”

(61.0 cm)

4” (10.2 cm)

2” (5.1 cm)

5 3/8”

(13.6 cm)

2” (5.1 cm) Min.

clearance

2” (5.1 cm)