STA RP LUS
TM
Triad Digital Systems Quick Reference Card
FIXED FEATURE BUTTONS
• CA MP - ON Button -- Enables you to alert a busy
party that an outside line is on hold and waiting
for th em.
• CONF (CONFERENCE) Button -- Used to
establish and build conference calls .
• FLASH Button -- Used to terminate an outside
call and restore dial tone without having to
hang up the handset. It is also used to transfer
calls behind a PBX or Centrex within those
sys tems.
• FORWARD (FWD) Button -- Allows you to
forward your calls to another station.
• HOLD Button -- Enables you to place an outside
caller on hold.
• H- T- P Switch -- Allows the user to select the ICM
signaling mode: Handsfree, Tone, or Privacy.
• MSG (MESSAGE WAIT) Bu tton -- Allows you to
initiate a message waiting indication at stations
that are busy, unattended, or in Do Not Disturb.
Message Waiting Callback request left at your
station is indicated by a flashing MSG WAIT LED.
• MUTE Button -- Allows you to switch the built-
in microp ho n e on or of f when us ing th e
speakerphone, or the handset microphone
when using the hands et.
• ON/OFF Button -- Enables you to make a
telephone call without lifting the handset. It
turns the telephone on and off when using the
speakerphone.
• SPEED Button -- Provides you with access to
speed dialing, save number redial an d last
number redial. This button is also used to
access flexible button programming.
• TRANS (T RA NSF ER) Button -- Used to transfer
an outside call from one station to another.
• VOLUME BAR -- Allows the user to adjust
speakerphone and handset volume.
CALL FORWA RDING
1. Pres s the FWD butto n or dial [6 40].
2. Dial t he des ired Call Forward co de:
[6] = All Calls
[7] = N o Answer
[8] = Busy
[9] = Busy/No Ans wer
3. Dial station number where calls are to be
forwarded. Hear confirmation tone.
4. Replac e h and set o r pr ess O N/ OFF bu tt on .
ESTABLISHING A CONFEREN CE
Only stations that have Conference enabled will be
able to initiate a Con ference.
1. Lif t the hand set.
2. Selec t in t ercom station or dial desir ed o ut side
party. When called party ans wers, press the
CO NF bu tton .
3. Add nex t conf erence party by s elec ting
another outside line or intercom station.
4. Press the CONF button again and repeat
previous step in a cycle, until all parties are
co nt act ed.
5. When last party answers, press the CON F
button twice. All parties are connected.
TERMINATI NG A CONFE RE NCE
To termin ate a Conference, the conf erence initiator
must be actively in the conference.
R eplace h and set or pr ess O N/ OFF butt on .
U NSCREEN ED TRA NS FER
1. Press TRANS button and dial station number.
2. When the called extension begins to signal,
hang up to transfer the call.
3. Rep lace handset o r pres s O N/OFF bu tto n.
SCREENED T RA NS FER
While connected to an outside line:
1. Press station button where call is to be
transferred (if programmed on your
te lep ho ne),
-o r-
Press the TRANS button and dial the desired
station number.
(The called extension signals according to the
intercom signal switch position.)
2. When that extension answers , announce the
tr ans fe r .
3. Hang up to complete transfer.
LEA VING A MS G WAITING INDICAT ION
If you dial a station that is busy, unattended, or in
Do Not Disturb, you can leave a message waiting
indication.
1. Press the ON/OFF butto n.
2. Dial the des ired intercom station. A busy tone
or DND tone is he ard.
3. Press the MSG button. The called party’s MSG
button LED will flash slowly.
4. Press the ON/Off button to end the call.
