Prodotti Del Marchio ADS-tec

Quick Start Guide Commissioning /Mounting IRF2000 series

120627_ QUICK START GUIDE IRF2000_DE_EN DZ-HAND-91056-0 V1.1

1. Scope of delivery 3. Connecting the device

1 x Industrial Router Firewall

1 x 3 pol. connector

2 x 4 pol. connector

1 x Rail mounting holder

2 x M4 x 6 Pan Head screw + 2 x M4 washer + 2 x Disk washer

4 x rubber feet

1 xEthernet cable 1m

1 x Quick Start Guide Commissioning /Mounting IRF2000 series

1 x GNU General Public License

Warning:

Any installation works on the device are only

permitted if the power supply is switched off, and

if handling the device is safe.

Note:

Please observe applicable security measures

when handling electronic components sensitive

to electrostatic charges.

(DIN EN61340-5-1 /

DIN EN 61340-5-2).

2.1 Table mounting

Remove the protective strip from the rubber feet and fix them to

the marked locations.

2.2 Wall mounting

The unit can be mounted alternatively via VESA 75 standard at a

suitable mounting surface.

2.3.Rail mounting

Install the supplied rail mounting holder in the following

order:

WasherRail mounting holderDisk washerPan Head

screw to the device.

The unit is set at an angle from the top of the rail (1) and is

fixed by gently pushing it to the bottom (2). The unit must

engage significantly in the rail.

To release the unit from the DIN rail, proceed in reverse

order.

Note:

When installing the rail mounting holder, there is

danger of injury from sharp edges.

Note:

Be carfeful not to damage the rail mounting

holder while removing it.

3.1. Power supply connection

The power for this device can be supplied by a 24V DC

(7…36V) (3 pin plug). The corresponding connector is

included in the scope of delivery. Connect the device with

a suitable power supply unit.

Once the power supply is connected to the device, the

PWR LED is solid green.

(Front view)

4.1. UMTS Functionality at IRF2210

This variant (IRF2210) offers UMTS-Functionality. A

UMTS-Antenna is supplied (1) and a 3G Card Reader

(2) is available.

5.1.RJ45 network cable connection

For initial commissioning it is essential to establish a

connection between this device and a PC. Connect the

LAN port of the device with a PC.

Note:

The device with default settings operates as

DHCP client on the WAN interface. You can

use the WAN interface to configure the device

if you have a DHCP server which does not

serve IPs from the 192.168.0.0 range.

PIN-

NUMBER

SIGNAL

NAME

1 24V DC

2 GND

3 PE

5.2. Configuration of the PC-LAN-Network adapter

Open the Properties tab of the used network adapter.

Use following IP address

Access to the device is only enabled once the following

parameters have been entered:

IP address: 192.168.0.100

Subnet mask: 255.255.255.0

(The last section of digits must represent a number

between 1 and 253; the value “100” has been selected in

the example)

5.3. Access the webinterface

Start your web browser in order to open the web interface

of this device. Now enter the following IP address into the

address line of your browser:

http://192.168.0.254

5.4. Login

In the Login prompt window, the default settings must be

entered. The default settings, as delivered to the

customer, are:

User name: admin

Password: admin

Confirm your entry by using OK. Now, the device web

interface will appear.

Note:

If you are using a Proxy, it has to be deactivated

if neccessary.

Note:

We would recommend to make use of our

website contents (www.ads-tec.de) in order to

ensure an optimised data quality and to be

quickly and comprehensively informed of any

technical modification.

2. Mounting

4. UMTS Functionality at IRF2210

5. Configuration