Dil ID: 7
Dil Adı: french
Dil Kodu: fr2tayfun Produits de la Marque Whirlpool
Dünyanın En Büyük
Elektronik Bilgi Kütüphanesi



Temperature
Every programme has a predened temperature. If you want to change
the temperature, press the Temperature
60°
40°
button. The value appears
on the display.
Spin
Every programme has a predened spin speed. If you want to change the
spin speed, press the “Spin button. The value appears on the display.
Demo mode
This appliance is equipped with Demo mode function. For more
information see the USER MANUAL/ Demo Mode.
KEY LOCK
To lock the control panel, press and hold the “Key lock” button for
approximately 3 seconds. The symbol will light up on the display
to indicate that the control panel has been locked (with the exception
of the “ON/OFF“ button). This prevents unintentional changes to
programmes, especially with children near the machine. To unlock the
control panel, press and hold the “Key lock” button for approximately
3 seconds .
BLEACHING
If you wish to bleach the laundry, load the washing machine and set the
“Rinse & Spin programme.
Start the machine and wait for it to complete the rst water lling cycle
(roughly 2 minutes). Put the machine in pause mode by pressing the
“Start/Pause button, open the detergent drawer and pour the bleach
(observe the recommended doses indicated on the package) into the
main wash compartment where the partition was previously mounted.
Restart the cycle by pressing the “Start/Pause button.
If desired, it is possible to add fabric softener into the appropriate
compartment of the detergent drawer.
HINTS AND TIPS
Sort your laundry according to
Type of fabric/care label (cotton, mixed bres, synthetics, wool, handwash
items). Colour (separate coloured and white items, wash new coloured
items separately). Delicates (wash small items like nylon stockings – and
items with hooks – like bras – in a cloth bag or pillow case with zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the
drum.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch o and unplug the washing
machine. Do not use ammable uids to clean the washing machine.
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing machine.
Do not use glass or general purpose cleaners, scouring powder or similar
to clean the control panel – these substances might damage the printing.
Checking the water supply hose
Check the inlet hose regularly for brittleness and cracks. If damaged,
replace it by a new hose available through our After-Sales Service or
your specialist dealer. Depending on the hose type: If the inlet hose has
a transparent coating, periodically check if the colour intensies locally. If
yes, the hose may have a leak and should be replaced
Cleaning the mesh lters in the water supply hose
Close the tap and loosen the inlet hose on the tap. Clean the internal
mesh lter and screw the water inlet hose back onto the tap. Now
unscrew the inlet hose on the rear of the washing machine. Pull o the
mesh lter from the washing machine connection with universal pliers
and clean it. Ret the mesh lter and screw the inlet hose on again. Turn
on the tap and ensure that the connections are completely water-tight.
Cleaning the water lter / draining residual water
If you used a hot wash programme, wait until the water has cooled down
before draining any water. Clean the water lter regularly, to avoid that the
water cannot drain after the wash due to obstruction of the lter. If the water
cannot drain, the display indicates that the water lter may be clogged.
Remove the plinth by using the screwdriver: push downwards one side
of the plinth with your hand, then push the screwdriver into the gap be-
tween plinth and front panel and pry open the plinth. Place a broad, at
container beneath the water lter, to collect the drain water. Slowly turn
the lter counterclockwise until water ows out. Let the water ow out,
without removing the lter. When the container is full, close the water
lter by turning it in clockwise. Empty the container. Repeat this proce-
dure until all the water has drained. Lay a cotton cloth beneath the water
lter, which can absorb a small amount of rest water. Then remove the
water lter by turning it out anti clockwise. Clean the water lter: remove
residues in the lter and clean it under running water. Insert the water
lter and reinstall the plinth: Reinsert the water lter again by turning it
in clockwise direction.
Make sure to turn it in as far as it goes; the lter handle must be in vertical
position. To test water tightness of the water lter, you can pour about 1
liter of water into the detergent dispenser. Then reinstall the plinth.
ACCESSORIES
Contact our After-Sales Service to check if the following accessories are
available for your washing machine model.
Stacking kit shelf
By which your dryer can be xed on top of your washing machine to save
space and to facilitate loading and unloading your dryer in the higher
position.
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
Pull out the mains plug, and close the water tap. Make sure that door
and detergent dispenser are properly closed. Disconnect the inlet hose
from the water tap, and remove the drain hose from your draining point.
Remove all rest water from the hoses, and x them so that they cannot
get damaged during transport. Ret the transport bolts. Follow the
instructions for removing the transport bolts in the INSTALLATION GUIDE
in reverse order.
EN
Quick guide