Data Sheet 85098-0003 Issue 2
Not to be used for installation purposes. Page 5 of 10
General
Description
Round clock, 12 in (30.5 cm), or 15 in (38.1 cm)
diameter
Arabic (1-12 or 0-23 hour) clock face
Matte charcoal-gray case
Connections Each clock is furnished with a cable assembly 18
in (45.7 cm) long with a polarized plug and mating
socket.
Wiring Red (correction coil)
Black (run motor)
White (common return)
Green/Shield (safety ground)
Frequency and Power Requirements
Correction Minute hand corrects hourly
Hour hand corrects every 12 hours
Coil Input Voltage 115Vac, 24Vac, or 24Vdc
Motor Input
Voltage
115Vac or 24Vac
Coil Input
Frequency
60Hz or DC
Motor Input
Frequency
60Hz
Coil Input Power 4 Watts
Motor Input
Power
4W (8W for double faced)
Mounting
Surface Mount to RACO 695 single-gang backbox or equal
(order separately).
Semiflush 24SS mounts to a 8-SAM0576 custom backbox. (Order
backboxes separately.)
Dimensions: 8 in (20.3 cm) high, 6 in (15.2 cm) wide, 3
in (7.6 cm) deep.
Double Faced Mount to a 4-inch (10.16 cm) by 4-inch (10.16 cm)
dual gang backbox (order separately). Adapter plates
are furnished with each assembly for wall or ceiling
mount. Specify wall or ceiling mount when ordering.
24CC10 Clock Controller
User-friendly front panel controls
Controls GE two-inch or four-inch
digital clocks
Operating modes: 12 or 24-hour clock; count down timer;
elapsed timer; score board; code blue elapsed timer
Operates independently or as slave to master clock
Timer display settings: hours/minutes; minutes/seconds
Operates from 15Vdc or 24Vac
Mounts in standard three or four-gang backbox
The GE Model 24CC10 Clock Controller is a compact, micropro-
cessor-controlled unit that enables a GE 24D20 Two-Inch Digital
Secondary Clock or 24D40A Four-Inch Digital Secondary Clock to
be used for count up timing, count down timing, score keeping
and code blue timing. The digital clock serves as the time indicator
and display for the clock controller in the room. The digital clock is
mounted for optimum visibility, while the clock controller is mount-
ed in a convenient location that allows access to its controls.
The Model 24CC10 Clock Controller is designed for ease of use, with
logical button groupings, intuitive labeling, and LED function guid-
ance. When a particular operating mode is selected, related LEDs
illuminate to indicate the commands available in that mode. A lock-
out feature allows the front panel controls to be disabled, prevent-
ing unauthorized use. The 24CC10 and its associated digital clock
can operate as a stand-alone clock/timer or as a secondary clock
•
•
•
•
•
•
under the corrective control of a GE Model 24A715 or 24A715M
Master Time/Program Clock. The 24CC10 can also operate under
the corrective control of a StarCall
®
, StarCare™ or MCS350 master
clock. The 24CC10 is powered by a separate 10 to 24Vac or 10 to
15Vdc power source. The 24CC10 has five operating modes:
Clock Mode displays the time on the GE digital clock in 12- or 24-
hour format. In clock mode, the clock controller operates under
the control of a master clock. In the absence of a master clock, the
clock controller can operate in stand-alone mode, governing the
time for its associated GE digital clock. Stand-alone mode does not
provide battery backup for the clock display, therefore GE recom-
mends that a master clock be used.
Count Down Timer Mode counts down to zero from a user-selected
start time. The timer can count down by minutes and hours or by
seconds and minutes. It can also be set to run silent, to beep when
the timer runs down to zero, to chirp once per minute and beep at
zero, or to chirp once per minute and once per second and beep at
zero. During the count down sequence the timer can be stopped,
restarted, and reset to its original target value.
Count Up Timer Mode measures the duration of an event. The timer
can count up by hours and minutes or by minutes and seconds. It
can also be set to run silent, to chirp once per minute, or to chirp
once per minute and once per second. During the count up se-
quence the timer can be stopped, restarted, and reset to the initial
timer value.
Score Board Mode uses the digital clock as a simple score board.
The two left digits of the clock display the score of team 1 and the
two right digits display the score of team 2.
Code Blue Timer Mode shows the elapsed time from when a code
blue call is placed to when the STOP button is pressed on the clock
controller. The code blue timer overrides anything currently dis-
played on the digital clock. This mode requires a contact closure
from a separate device that initiates code blue calls.
Specifications: 24CC10 Clock Controller
Operating
Voltage
24Vac nominal—recommended (10Vac min. to 30Vac
max.)
—or—
15Vdc nominal (10Vdc min. to 30Vdc max.)
Current
Consumption
91mA @ 10Vac, 50mA @ 24Vac
—or—
110mA @ 10Vdc, 75mA @ 15Vdc
Terminations Two pigtail connectors with 8 leads each (provided)
One pigtail connector with 2 leads (for code blue;
provided)
Operating
Temperature
32°–90° F (0°–32° C)
Dimensions 4-1/8 in (10.5 cm) high x 8 in (20.3 cm) wide x 1-1/2 in
(3.8 cm) deep
Weight Approximately 9 ounces (252 g)
Mounting Flush mounts into RACO 3 or 4-gang backbox, 2.5 in
(6.4 cm) deep
Finish Bezel—textured gray ABS
Panel—textured gray polycarbonate
110-3902 Dual Four-inch Digital Clock Housing
Dimensions 7 in (17.8 cm) high, 19 in (48.3 cm) wide, 4-1/2 in
(11.43 cm) deep
Weight 4.4 lbs (2 kg), less backbox and clocks
Mounting Wall-mounted using two-gang masonry box
Ceiling-mounted using conduit extensions
Finish Charcoal gray
