12
To register a handset:
Place the new/non-registered handset in the telephone base.
The handset shows Registering... Please wait, then Handset X Registered
and you hear a beep when the registration process completes. The registration
process takes about 90 seconds to complete.
You can add one more cordless headset (IS6100, purchased separately) to
your telephone system. The headset must be registered with the telephone base
before use.
To register a headset:
Press and hold FIND HANDSET on the telephone base for about 4 seconds
until the IN USE light turns on. Then release the button.
Immediately place the new/non-registered headset on the telephone base. It
takes about 60 seconds to complete the registration process. Do not remove
until the IN USE light goes off.
Deregister handsets/headset
If you want to replace a handset/headset or reassign the designated handset
number of a registered handset, you must deregister all devices, including all
handsets and headsets. Then individually register each device again.
To deregister all devices:
Press and hold FIND HANDSET on the telephone base for about 10 seconds
until the IN USE light on the telephone base turns on and starts ashing.
Immediately press FIND HANDSET again. You must press FIND HANDSET
while the IN USE light is still ashing. The IN USE light ashes for approximately
ve seconds.
All handsets show To register HS, see manual. when the deregistration process
completes. The deregistration process takes about 10 seconds to complete.
Troubleshooting
If you have difculty with your telephone, please try the suggestions below. For customer service,For customer service,
visit our website at www.vtechphones.com or call 1 (800) 595-9511.
In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.
I cannot add and connect my cell phone to the telephone base.
Make sure you have cellular coverage.
Make sure your cell phone is compatible with your DS6671/DS6672. Check the Bluetooth
compatibility list at www.vtechphones.com.
Make sure the Bluetooth function of your cell phone is turned on. See the user’s manual of your cell
phone for more information.
Make sure that your Bluetooth cell phone is not connected to any other Bluetooth device.
To connect your cell phone, make sure that your cell phone is connected and active on the
device list.
Remove VTech DS6671/VTech DS6672 from your cell phone’s handsfree device history list (see
the user’s manual of your cell phone for more information).
Carefully follow the pairing instructions on page 6 and make sure that your cell phone is not
connected to any other Bluetooth device.
Turn off your cell phone, then turn it on again.
For some cell phones, you must authorize VTech DS6671/VTech DS6672 device in your cell
phone’s Bluetooth feature. See the user’s manual of your cell phone for more information.
Manually connect your cell phone to VTech DS6671/VTech DS6672. Refer to the user’s manual of
your cell phone for more information.
Reset the telephone base. Unplug the unit’s electrical power. Wait for approximately 15 seconds,
then plug it back in. Repeat the above suggestions.
The PIN on the telephone base does not work.
Make sure you enter the correct PIN. The default PIN is 0000.
My telephone does not work at all.
Make sure the battery is installed and charged correctly. For optimum daily performance, return the
handset to the telephone base or charger after use.
Make sure the power adapter is securely plugged into an outlet not controlled by a wall switch.
Make sure the telephone line cord is plugged rmly into the telephone base and the wall jack.
Unplug the electrical power to the telephone base. Wait for approximately 15 seconds, then plug
it back in. Allow up to one minute for the cordless handset and telephone base to synchronize.
Charge the battery in the handset for up to 12 hours.
If the battery is completely depleted, charge the handset for at least 30 minutes before use.
Remove the battery and then install it again. If that still does not work, it may be necessary to
purchase a new battery.
Disconnect the telephone base from the telephone wall jack and plug in a working telephone. If the
other telephone does not work, the problem is probably in the wiring or telephone service. Contact
your telephone service provider.
1.
2.
1.
2.
1.
2.
3.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not place the handset in the charger.
