ASA Electronics Brand's Products

-11

Introduction

Optional lenses

 Lens Projection distance for 100" screen size

Wide-zoom lens ( × 1.5 — 1.9) AN-C12MZ 10’ 5" — 13’ 1" (3.2 m — .0 m)

T ele-zoom lens ( × 2.2 — 2.8) AN-C18MZ 15’ 7" — 19’ 10" (.8 m — 6.0 m)

T ele-zoom lens ( × 3.3 — 5.1) AN-C27MZ 23’ 2" — 35’ 8" (7.1 m — 10.9 m)

T ele-zoom lens ( × 5.1 — 7.2) AN-C1MZ 36’ 2" — 50’ 10" (11.0 m — 15.5 m)

The standard zoom lens is attached to the projector.

The optional lenses from Sharp are also available for specialized application. Please see

your nearest Sharp Authorized Projector Dealer for details on all the lenses. (Refer to the

SETUP MANUAL on the supplied CD-ROM for details.) Also, be sure to have service person-

nel install the optional lenses.

Throw Distance

The graph below is for 100 inches (254 cm) screen with 16:10 Signal Input (Normal Mode).

Screen

10 20 30 5040 55(ft)

Standard zoom lens

12’4"—14’9" (3.8 m—4.5 m)

Throw distance ratio 1:1.8—2.1

Tele-zoom lens (AN-C18MZ)

15’7"—19’10" (4.8 m—6.0 m)

Throw distance ratio 1:2.2—2.8

Tele-zoom lens (AN-C27MZ)

23’2"—35’8" (7.1 m—10.9 m)

Throw distance ratio 1:3.3—5.1

Tele-zoom lens (AN-C41MZ)

36’2"—50’10" (11.0 m—15.5 m)

Throw distance ratio 1:5.1—7.2

Wide-zoom lens (AN-C12MZ)

10’5"—13’1" (3.2 m—4.0 m)

Throw distance ratio 1:1.5—1.9

Downloaded From projector-manual.com Sharp Manuals

-17

Quick Start

Pages 31, 32

4. Adjust the angle

5. Adjust the focus and the zoom

7. Tu rn the Power off

Page 30

6. Select the INPUT mode

Page 34

••

•

This projector is equipped with an ÒAuto V-Keystone

CorrectionÓ function that automatically corrects any

trapezoidal distortion within the projected image.

Bring the projected image into focus

••

• Bring the projected image into focus by

rotating the focus ring.

Adjust the projected image size

••

• Adjust the projected image size by moving the

zoom knob.

Select the ÒCOMPUTER 1Ó using the INPUT buttons on the projector or the COMPUTER 1 button on the remote control.

••

•

When you press the INPUT buttons on the projector, the INPUT list appears.

Press

’’

’ /

" to select an item on the list, and press ENTER to switch to the selected INPUT mode.

••

• When using the remote control, press COMPUTER1 /2, DVI , S-VIDEO or VIDEO to

switch the INPUT mode.

On the remote

control

On the

projector

" INPUT list

Press the STANDBY button, then press that button again while the confirmation message is displayed, to put the projector into standby mode.

••

• Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.

On the remote controlOn the projector

" On-screen Display

Adjust the projector angle

••

•

Adjust the projector angle using the Height

Adjustment buttons.

••

•

Rotate the Tilt dial to adjust the horizontal tilt of

the projector.

Height Adjustment

buttons

Tilt dial

Focus ring

Zoom knob

Zoom in

Zoom out

" On-screen Display (RGB)

RGB

1024 × 768

COMPUTER1

INPUT

COMPUTER1

COMPUTER2

DVI-D Computer

Page 33

Downloaded From projector-manual.com Sharp Manuals

-23

Connections

Connecting to a Computer

Before connecting, ensure the power cord of the projector from the AC outlet is unplugged,

and that the devices to be connected are turned off. After making all connections, turn on the

projector and then the other devices. When connecting a computer, ensure that it is the last

device to be turned on after all the connections are made.

Ensure the operation manuals of the devices to be connected have been read before making connections.

When connecting with the RGB cable

(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)

To audio output terminal

To RGB output terminal

* ¿3.5 mm stereo or mono audio cable

(commercially available or available as Sharp service part QCNWGA038WJPZ)

To COMPUTER/

COMPONENT 1

input terminal

Computer

To AUDIO input terminal

RGB cable

When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.

Note

• See page 65 “Computer Compatibility Chart” for a list of computer signals compatible with the projector.

Use with computer signals other than those listed may cause some of the functions to not work.

• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest

Macintosh Dealer.

• Depending on the computer you are using, an image may not be projected unless the computerÕs

external output port is switched on. (e.g. Press ÒFnÓ and ÒF5Ó keys simultaneously when using a

SHARP notebook computer). Refer to the specific instructions in your computer’s operation manual to

enable your computer’s external output port.

RGB cable

Supplied

accessory

Downloaded From projector-manual.com Sharp Manuals

-25

Connections

Connecting to Video Equipment

The image quality is highest in order of the Component signal, the RGB signal, the S-video signal and the

Video signal. If your audio-visual equipment has a component output terminal or RGB output terminal, use the

COMPUTER/COMPONENT terminal 1 or 2 on the projector for video connection.

When connecting video equipment with a DVI output terminal

Note

• Select the input signal type of the video equipment. See page 47.

• While the projector is connected to video equipment that has an HDMI output terminal, only the video

signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)

• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission

may not work property. (The HDMI specification does not support all connections to video equipment

that has HDMI digital output terminal using HDMI to DVI digital cable.)

• For details on compatibility for connection, see support information on DVI connection provided by the

video equipment manufacturer.

When connecting video equipment with component video output terminal

(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)

Note

• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a

commercially available cable that fits in the projector terminal you want to connect.

• The projector does not support RGBC signals via the Euro-scart.

DVI Digital cable (commercially available)

To audio output terminals

¿3.5 mm stereo minijack to RCA audio cable

(commercially available)

To DVI output terminal

Video Equipment

To DVI-D

input terminal

To AUDIO input terminal

(for COMPUTER/COMPONENT 2, DVI-D)

To audio output terminal

¿3.5 mm minijack to RCA audio cable (commercially available)

3 RCA (Component) to 15-pin D-sub cable

(optional: AN-C3CP2)

To component video output terminal

To COMPUTER/COMPONENT 1

input terminal

To AUDIO

input terminal

Video Equipment

Downloaded From projector-manual.com Sharp Manuals

-41

Useful Features

ÒScreen adjustment (SCR-ADJ)Ó menu

Off

Main Menu Sub Menu

OSD Display

Background

Logo

Blue

None

Normal

Full

Dot By Dot

Area Zoom

V-Stretch

Stretch

Center

Upper Right

Lower Right

Upper Left

Lower Left

Menu Position

Page 50

Resize

Page 49

Page 50

Auto V-Keystone

Page 49

+40-40

Image Shift

V-Keystone

Page 49

+100-100

H-Keystone

SCR-ADJ

Page 49

Language

Page 50

Front

Ceiling + Front

Rear

Ceiling + Rear

PRJ Mode

Page 50

English

Deutsch

Español

Nederlands

Français

Italiano

Svenska

Português

polski

Magyar

Türkçe

+60-60

ÒSignal adjustment (SIG-ADJ)Ó menu

Off

SIG-ADJ

+30-30

+60-60

+150-150

Clock

Phase

H-Pos

V-Pos

Reset

Signal Info

Resolution

Main Menu

Auto Sync

Page 47

Page 48

Signal Type

Page 47

Page 48

Auto

RGB

Component

Dynamic Range

Auto

Standard

Enhanced

Auto

PAL

SECAM

NTSC4.43

NTSC3.58

PAL-M

PAL-N

PAL-60

Video System

Page 48

* Item when inputting RGB signal through COMPUTER/COMPONENT 1 or 2

*5 Item when inputting COMPUTER/COMPONENT 1 or 2

*6 Item when selecting COMPUTER/COMPONENT 1, 2 or DVI-D

*7 Item when selecting DVI-D

*8 Item when selecting VIDEO or S-VIDEO

Downloaded From projector-manual.com Sharp Manuals

-47

Useful Features

Phase

Clock

Pict. SIG

–

ADJ SCR PRJ Net.

H-Pos

V-Pos

Reset

Auto

640 x 480

Standard

Auto

SEL./ADJ.

RETURN

ENTER

END

Resolution

Auto Sync

Signal Type

Dynamic Range

Video System

Signal Info : 800 x 600

H 60.3 kHz / V 37.8 Hz



Signal Adjustment (ÒSIG-ADJÓ Menu)

Adjusting the Computer Image

If the optimum image cannot be obtained with Auto

Sync adjustment, use the SIG-ADJ function.

Note

• To reset all adjustment items, select Reset and

press ENTER.

• The adjustable range of H-Pos (H-Position)

and V-Pos (V-Position) may vary depending

on the screen resolution of the computer.

Selectable items

Clock

Phase

H-Pos

V-Po s

Description

Adjusts vertical noise.

Adjusts horizontal noise (similar to

tracking on your VCR).

Centers the on-screen image by

moving it to the left or right.

Centers the on-screen image by

moving it up or down.

Resolution Setting

Ordinarily, the type of input signal is detected and the

correct resolution mode is automatically selected. How-

ever, for some signals, the optimal resolution mode in

Ò ResolutionÓ on the Ò SIG-ADJÓ menu may need to be

selected to match the computer display mode.

Note

• See Chec king the Input Signal on page 48 for

information on the currently selected input sig-

nal.

Auto Sync Adjustment

Used to automatically adjust a computer image.

Note

• Auto Sync adjustment is also performed by

pressing AUTO SYNC on the projector or on

the remote control.

• The A uto Sync adjustment may tak e some time

to complete, depending on the image of the

computer connected to the projector.

Selectable items

Off

Description

A uto Sync adjustment will occur when

the projector is turned on or when the

input signals are switched, when

connected to a computer.

A uto Sync adjustment is not automati-

cally perfor med.

Menu operation

Page 43

Signal Type Setting

This function allows you to select the input sig-

nal type RGB or Component for COMPUTER/

COMPONENT 1, 2 or DVI-D.

Description

Input signals are automatically recog-

nized as RGB or component.

Set when RGB signals are received.

Set when Component signals are

received.

Selectable items

A uto

RGB

Component

Downloaded From projector-manual.com Sharp Manuals

-49

Useful Features

Resize

Image Shift

H-Keystone

V-Keystone

Auto V-Keystone

Center

Normal

Logo

Front

English

SEL./ADJ.

RETURN

ENTER

END

OSD Display

Background

Menu Position

PRJ Mode

Language

Pict. SIG SCR-ADJ PRJ Net.



Screen Adjustment (ÒSCR-ADJÓ Menu)

Menu operation

Page 43

Setting the Resize Mode

Note

• F or details of the Resize mode, see pages 37

and 38.

• Y ou can also press RESIZE on the remote con-

trol to set the resize mode. (See page 37.)

Adjusting the Image Position

You can move the projected image vertically.

Note

• This function only works in some RESIZE

modes. (See pages 37 and 38.)

• To reset this function, select 0.

| button

\ \

\ button

Keystone Correction

When the image is projected either from the top or from

the bottom towards the screen at an angle, the image be-

comes distorted trapezoidally. The function for correct-

ing trapezoidal distortion is called Keystone Correction.

A uto V-Keystone Correction

Set ÒAuto V-KeystoneÓ on the ÒSCR-ADJÓ screen

menu to ÒOnÓ.

Manual Keystone Correction

Set ÒAuto V-KeystoneÓ on the ÒSCR-ADJÓ screen

menu to ÒOffÓ. Select ÒV-KeystoneÓ, and then

press

\ or

| to parallelize the left and right sides

of the projected image with the slide bar. To

parallelize the upper and lower sides, select ÒH-

KeystoneÓ and press

\ or

| .

Note

•

The Keystone Correction can be adjusted up to

an angle of approximately –12 degrees with Auto

V- Ke ystone and up to an angle of approximately

–50 degrees with V-Keystone and approxi-

mately –30 degrees with H-Keystone.

• When the screen is slanting or the image is de-

teriorated, set Auto V-Keystone to Off.

Horizontal Keystone Correction

Vertical Keystone Correction

Downloaded From projector-manual.com Sharp Manuals

-51

Useful Features

Auto Power Off

Auto Restart

System Sound

Speaker

Audio Out

9600bps

Enable

FAO

Enable

Normal

Disable

SEL./ADJ.

RETURN

ENTER

END

Monitor Out

LAN/RS232C

RS-232C

Fan Mode

System Lock

All reset

Lamp Timer (Life) [ 0]h [ 0] min ( 100%)

Pict. SIG SCR PRJ-ADJ Net.



Menu operation

Page 43

Description

The projector automatically enters the

standby mode when no input signal is

detected for 15 minutes or longer.

The Auto Power Off function will be

disabled.

Selectable items

Off

Auto Power Off Function

Note

• When the Auto Power Off function is set to ÒOnÓ,

5 minutes before the projector enters the

standby mode, the message ÒEnter STANDBY

mode in X min.Ó will appear on the screen to

indicate the remaining minutes.

Description

If the power cord is unplugged from the

outlet or the breaker switch is turned off

when the projector is on, then the

projector automatically turns on when

the power cord is plugged into the AC

outlet or the breaker switch is turned on.

The projector does not turn on auto-

matically when the power cord is

plugged into the AC outlet or the

breaker switch is turned on.

Selectable items

Off

2 Auto Restart Function

Description

A confirmation sound is made when the

projector turns on/off.

No confirmation sound is made.

Selectable items

Off

Setting the Confirmation

Sound (System Sound)

Helpful Functions Set during Installation (ÒPRJ-ADJ Ó menu)

Speaker Setting

This function allows you to set the audio output

of the internal speaker to ÒOnÓ or ÒOffÓ such as

when the projector is connected to an external

amplifier.

Selectable items

Off

Description

The audio signal is output from the internal

speaker.

The audio signal is not output from the

internal speaker.

Audio Output Type Setting

This function determines whether the audio level

output from the AUDIO output (MONITOR output)

terminal is fixed or variable by linking with VOL-

UME.

Info

• When ÒAudio OutÓ has been set to ÒVAOÓ, first make

sure to lower the volume of the projector before

turning the power on or off and when switching the

input.

Description

Audio output that does not vary in

strength with the volume level of the

source projector.

Audio output that varies in strength with

the volume level of the source projector.

Selectable items

FAO

(Fixed Audio

Output)

VAO

(Variable

Audio Output)

Monitor Output

LAN/RS232C

When set to ÒEnableÓ, the function is activated

and power is consumed even in the standby mode.

It is recommended that the function be set to ÒDis-

ableÓ when it is not connected. This reduces power

consumption when the projector is in the standby

mode.

Description

The function is activated even if the

projector is in standby mode.

The function is switched off when the

projector is in standby mode.

Selectable items

Enable

Disable

Note

• When you want to control the projector using

the LAN/RS232C function, select ÒEnableÓ.

Downloaded From projector-manual.com Sharp Manuals

-53

Useful Features

Menu operation

Page 43

Enter the same keycode in ÒRe-con-

firmÓ.

Note

To cancel the keycode that you have al-

ready set

• Press " on the projector for four times in steps

4 and 5 above.

When the System Lock is set

• When System Lock is set, the keycode input screen

appears after the power is turned on. When it ap-

pears, enter the right keycode to start projection.

Input screen for keycode

Info

• Keylock cannot be set while the projector is: dis-

playing the “Menu” screens, in standby mode,

warming up, changing input signals, operating

“Auto Sync” function or on the “System Lock”

screen during warming up.

System Lock

––––

Keylock Function

Locking the Operation Buttons on

the Projector

Use this function to lock the operation but-

tons on the projector.

 Locking the Operation Buttons

Hold down ENTER on the projector for about 5 sec-

onds while the projector is being turned on.

 On-screen Display

Keylock function ON

• The keylock function does not affect the operation

with the remote control buttons.

• You cannot use the keylock function while the pro-

jector is warming up.

 Taking the Keylock off

Hold down ENTER on the projector for about 5 seconds.

 On-screen Display

Keylock function OFF

• When the projector is in standby mode, you can

release the keylock by holding down ENTER and

STANDBY/ON on the projector simultaneously for

about 5 seconds.

Returning to the Default

Settings

This function allows you to initialize the settings

you have made in the projector.

Note

The following items or menu cannot be initialized.

• “SIG-ADJ” menu

Resolution

• “SCR-ADJ” menu

Language

• “PRJ-ADJ” menu

Lamp Timer (Life)

System Lock

w Checking the Lamp Life

Status

You can confirm the cumulative lamp usage time

and the remaining lamp life (percentage).

Note

• It is recommended that the lamp be changed

when the remaining lamp life becomes 5%.

• Remaining lamp life changes within the range

of the values shown depending on the frequency

at which “Eco+Quiet Mode” is switched to “On”

and “Off”. (See page 46.)

• The lamp life may vary depending on the us-

age condition.

Lamp usage condition

“Life”

Operated exclusively

while “Eco+Quiet Mode”

is “On”.

Operated exclusively

while “Eco+Quiet Mode”

is “Off”.

Remaining lamp life

100% 5%

Approx. Approx.

3,000 hours 150 hours

Approx. Approx.

2,000 hours 100 hours

Downloaded From projector-manual.com Sharp Manuals

-63

Appendix

User service screw

(for lamp unit cover)

AC socket

5 Insert the new lamp unit.

• Press the lamp unit firmly into the lamp

unit compar tment. Fasten the securing

screws.

6 Replace the lamp unit cover.

• Align the lamp unit cover and slide it to

close. Then tighten the user service

screw to secure the lamp unit cover.

Info

• If the lamp unit and lamp unit cov er are not

correctly installed, the power will not turn

on, even if the power cord is connected to

the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

• Make sure to reset the lamp timer only

when replacing the lamp. If you reset the

lamp timer and continue to use the same

lamp, this may cause the lamp to become

damaged or explode.

• Y ou can also reset the lamp timer via the

LAN.

(Ref er to the SETUP MANUAL on the sup-

plied CD-ROM for details.)

1 Connect the power cord.

• Plug the power cord into the AC socket

of the projector.

2 Reset the lamp timer.

•

While simultaneously holding down " ,

ENTER and MENU on the projector,

press STANDBY/ON on the projector and

k eep all four buttons pressed down until

the lamp indicator starts blinking green.

• LAMP 0000H is displayed, indicating

that the lamp timer is reset.

" button

ENTER button

STANDBY/ON button

Lamp indicator

MENU button

Downloaded From projector-manual.com Sharp Manuals

-65

Appendix

Note

• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD)

mode. Should this occur, turn off the LCD display on the notebook computer and output the display data

in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s

operation manual.

• When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.

• When projecting the RGB interlace signal using COMPUTER/COMPONENT 1, 2 or DVI-D with “Signal Type”

set to “Auto” or “RGB”, the image may not be projected as desired. In this case, use either Video or S-Video.

• Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution”

adjustment. Check the settings of the computer’s signal output. If the settings cannot be changed, it is recom-

mended that the resolution be set to the one that corresponds to “1280 × 800”.

Computer Compatibility Chart

• Multiple signal support

Horizontal Frequency: 15–110 kHz

Ver tical Frequency: 43–85 Hz

DTV

Computer

Pixel Clock: 12–170 MHz

Sync signal: Compatible with TTL level

• Compatible with sync on green signal



Mode Resolution VESA

Vertical Frequency

(Hz)

Analog RGB

Support

Digital RGB

Support

Horizontal Frequency

(kHz)

VGA

SVGA

XGA

WXGA

SXGA

SXGA+

UXGA

MAC 13"

MAC 16"

MAC 19"

MAC 21"

640 × 350

640 × 400

720 × 350

720 × 400

640 × 480

800 × 600

1024 × 768

1280 × 720

1280 × 768

1280 × 800

1360 × 768

1366 × 768

1152 × 864

1280 × 1024

1400 × 1050

1600 × 1200

640 × 480

832 × 624

1024 × 768

1152 × 870

27.0

31.5

37.9

27.0

31.5

37.9

27.0

31.5

27.0

31.5

37.9

26.2

31.5

34.7

37.9

37.5

43.3

31.3

35.2

37.9

46.6

48.1

46.9

53.7

40.3

48.4

56.5

60.0

68.7

45.0

47.8

49.7

62.8

47.7

47.8

55.0

66.2

67.5

64.0

80.0

64.0

65.3

75.0

34.9

49.7

60.2

68.7

15.7

31.5

33.8

15.6

31.3

37.5

45.0

28.1

33.8

56.3

67.5

480

480P

540P

576

576P

720P

1080

1080P

Signal Vertical Frequency (Hz) DVI SupportHorizontal Frequency (kHz)



The following is a list of modes that conform to VESA. However, this projector supports other signals

that are not VESA standards.

Downloaded From projector-manual.com Sharp Manuals

-67

Appendix

CheckProblem Page

An unusual sound is

occasionally heard

from the cabinet.

Maintenance

indicator illuminates or

blinks in red.

The projector cannot be

turned on or put into the

standby mode using the

STANDBY/ON button on

the projector.

Picture is green with

component input signals

(COMPUTER/

COMPONENT 1, 2, DVI-D)

Picture is pink (no green)

with RGB input signals

(COMPUTER/

COMPONENT 1, 2, DVI-D)

Picture is too bright and

whitish.

The black levels of the

image show banding or

appear faded when DVI-

D is selected.

The cooling fan

becomes noisy.

The lamp does not light

up even after the

projector turns on.

The lamp suddenly turns

off during projection.

The image sometimes

flickers.

The lamp takes a long

time to turn on.

Picture is dark.

The remote control

cannot be used.

• If the picture is normal, the sound is due to cabinet shrinkage

caused by room temperature changes. This will not affect

operation or performance.

• See “Maintenance Indicators”.

• The keylock is set.

If the keylock is set to ON, all the buttons are locked.

• Change the input signal type setting.

• Image adjustments are incorrectly set.

• Select the Dynamic Range setting (“Standard” or “Enhanced”)

that results in the best picture quality.

• When temperature inside the projector increases, the cooling

fan runs faster.

• The lamp indicator is illuminating in red.

Replace the lamp.

• Cables incorrectly connected to the projector or the connected

equipment works improperly.

• If this happens frequently, replace the lamp.

• The lamp will eventually need to be changed.

The lamp has reached the end of its life. Replace the lamp.

• Operate the remote control while pointing it at the projector’s

remote control sensor.

• The remote control may be too far away from the projector.

• If direct sunlight or a strong fluorescent light is shining on the

projector’s remote control sensor, place the projector where it

will not be affected by strong light.

• The batteries may be depleted or inserted incorrectly. Make

sure the batteries are inserted correctly or insert new ones.

—

23-29

This projector is equipped with a microprocessor. Its performance could be adversely affected by

incorrect operation or interference. If this should happen, unplug the projector and plug it in again

after more than 5 minutes.

Downloaded From projector-manual.com Sharp Manuals

-69

Appendix

Specifications

As a part of policy of continuous improvement, SHARP reserves the right to make design

and specification changes for product improvement without prior notice. The performance

specification figures indicated are nominal values of production units. There may be some

deviations from these values in individual units.

Model

Display devices

Resolution

Lens

Input terminals

Output terminals

Control and

communication

terminals

Speakers

Projection lamp

Rated voltage

Rated frequency

Input current

Po w er consumption (Standby)

Operation temperature

Cabinet

Dimensions (main body only) [W × H × D]

W eight (approx.)

F number

Zoom

F ocus

D VI-D (Compatible with HDCP)

Computer/Component

(mini D-sub 15 pin)

S-Video (mini DIN  pin)

Video (RCA)

A udio (¿3.5 mm stereo minijack)

A udio (RCA)

Computer/Component

(mini D-sub 15 pin)

A udio (¿3.5 mm stereo minijack)

LAN (RJ-5)

USB (Type B)

RS-232C (mini DIN 9 pin)

Wired Remote

(¿3.5 mm stereo minijack)

XG-C55W/PG-C355W

0.7" LCD panel × 3

WXGA (1280 × 800)

F 1.7 — 1.9

Manual, × 1.2 (f = 28.0 — 33.6 mm)

Manual

× 1

× 2

× 1

× 2

× 2 (L/R)

× 1

× 1 (variable audio output)

× 1

2 W (Mono)

275 W

AC 100 — 20 V

50/60 Hz

3.6 A

360 W (3. W) with AC 100 V

35 W (. W) with AC 20 V

1 ° F to 95 ° F (+5 ° C to +35 ° C)

Plastic

" × " × 11

6

(326 × 101.5 × 279.5 mm)

10.8 lbs. (.9 kg)

Downloaded From projector-manual.com Sharp Manuals