37593 1
© Copyright 2004, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without
the expressed written consent of the publisher.
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Table of Contents
Section 1 – Safety Information
Locating an Authorized Servicer ............................4
Section 2 – Introduction
Customer Service ....................................................5
Nameplate Location ................................................5
Model Identification ................................................6
Section 3 – Troubleshooting
1. No Hot Water ...................................................7
2. No Cold Water .................................................7
3. No Warm Water ...............................................8
4. Water Fill Does Not Stop At Proper Level ......8
5. Timer Does Not Advance (Mechanical Timer
Models Only) ...................................................9
6. Motor Does Not Run ......................................10
7. No Agitation ...................................................10
8. Constant Agitation .........................................11
9. Washer Smokes, Overheats, Cycles On Motor
Thermal Overload Protector, Switch Actuator
Kicks In And Out ...........................................11
10. Slow Spin Or No Spin ....................................12
11. Constant Spin .................................................12
12. Washer Stops In Cycle; Quits After A Couple
Loads; Is Intermittent .....................................13
13. Washer Is Locked Up Or Binding ..................13
14. Outer Tub Does Not Empty ...........................13
15. Excessive Vibration .......................................14
16. Water Leaking From Outer Tub .....................14
17. Troubleshooting Coin Drop ...........................15
Electronic Control Models
18. Error Code Listing .........................................17
19. Cannot Perform Infrared Communication .....18
20. Coins Ignored When Entered .........................19
21. Electronic Control Has No Visible Display ...20
22. No Fill Analysis .............................................22
23. No Motor Run — Agitate Analysis ...............24
24. No Motor Run — Spin Analysis ....................26
25. Overflow Analysis .........................................28
26. Audit Switch Function Analysis ....................30
Section 4 – Grounding
27. Wall Receptacle Polarity Check ....................31
28. Power Cord To Control Hood, Control Hood To
The Control Panel Frame ...............................31
29. Control Hood Wire Harness To Top Left Rear
Corner Gusset Of Cabinet ..............................32
30. Wire Harness To Motor .................................32
Section 5 – Service Procedures
31. Control Panel Assembly ................................33
32. Timer Assembly .............................................37
33. Meter Or Timer Case Assembly ....................39
34. Coin Drop .......................................................40
35. Drain Hose Elbow ..........................................45
36. Loading Door .................................................45
37. Front Panel .....................................................47
38. Motor And Mounting Bracket .......................47
39. Idler Lever And Pulley ...................................49
40. Motor Drive Pulley ........................................50
41. Motor Switch .................................................53
42. Agitator ..........................................................54
43. Cabinet Top Assembly ...................................54
44. Cabinet Top Assembly Removal ...................55
45. Agitator Drive Bell and Seal Kit,
No. 39508P ....................................................56
46. Out-of-Balance Switch Assembly ..................59
47. Mixing Valve Assembly ................................60
48. Outer Tub Cover And Clothes Guard ............61
49. Hub and Seal Kit, No. 495P3 .........................65
50. Outer Tub Assembly ......................................67
51. Drive Pulley and Helix ...................................70
52. Brake Assembly .............................................72
53. Lower Bearing Housing .................................73
54. Transmission Assembly .................................73
55. Balance Ring ..................................................78
56. Upper Bearing Assembly ...............................78
57. Snubber Pad and Isolator Assembly ..............79
Section 6 – Adjustments
58. Leveling Legs .................................................81
59. Pressure Switch ..............................................82
60. Out-of-Balance Switch ...................................82
61. Belt (Agitate and Spin) ..................................82
62. Idler Spring Tension ......................................83
63. Cleaning Coin Drop .......................................84
(continued)
