Whirlpool is a registered trademark of Whirlpool USA
5019 396 01091
Before using the dishwasher, read the
installation and maintenance instructions carefully!
1
GB
ADG 9928
1) Programme data obtained in conformity with European standard EN 50242. Values may vary in relation to usage, e.g.
different loads, options, different sensor settings (only with sensor programmes), different water supply temperatures, as well
as water hardness and power supply voltage.
2) Reference programme for energy label in compliance with EN 50242. - Important information for Test Laboratories:
for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
“nk_customer@whirlpool.com”.
1. OVERVIEW
On button
Off button
Time and failure display
With “Delayed start” selected, it indicates the time
remaining until the start of the programme (hh). Toward
the end of the programme, during the drying cycle, the
display will indicate the time remaining in minutes.
If “F..” appears on the display, see chapter 5 “What to do if ...”.
Delayed start button
The wash cycle can be programmed to start after
1- 24 hours (with each successive touch of the button,
the delayed start indicator increases by 1 hour, and after
24 returns to 00).
Then press the START button. The dishwasher will start
at the set time.
Detergent setting upon initial use and when using a different type of
detergent
1. Press and hold the programme selection button, also press the
“Delayed start” button. The selected detergent type will be shown
on the display.
2. Using the delayed start button, select the desired detergent
(“--” = powder detergent, “2 l” = 2 in 1, “3 l” = 3 in 1, “A l” = all
other combined action detergents (in this way, the rinse aid and/or
salt indicator is deactivated). The selected detergent type will be
shown on the display.
3. Wait 5 seconds or switch off the appliance, the selected detergent
type is memorised. It is shown on the display for approx. 3 seconds
after the appliance is switched on. Note that only after changing the
detergent type is it possible to select the desired programme and, if
necessary, select the delayed start button.
Programme selection button
Press the button repeatedly until the desired programme
indicator lights up.
Start button
Switches “on” when the dishwasher is operating.
Flashes when a fault occurs. Switches off at the end of
the programme.
START button RESET function:
Press this button for at least 2 seconds; the selected
programme and options are cancelled. Main failure
displays (repeated flashing of the START indicator lamp)
can be cancelled by RESETTING. Detailed instructions
are given in chapter 5 “What to do, if...”.
Rinse aid level indicator and salt level indicator
These indicator lamps light up when rinse aid or salt
need to be added.
Add just before starting a wash programme.
Running programme indicator
A LED light projected on the floor indicates that the
dishwasher is working.
Table 1.1.
Programme chart
Detergent
dispenser
Consumption
1)
P
Programmes
Available
options
Loading instructions large small Litres kWh Minutes
1
Auto Sensor 50-65°C
Recommended programme for
routine washes, with dried-on
food (e.g. EN 50242).
X X 11-16 1.10-1.50 100-130 ±
1)
2
Rapid 40°C
Lightly soiled crockery, with no
dried-on food.
X — 10.0 0.65 30 ±
1)
3
Eco
2)
50°C
Normally soiled crockery.
Energy saving programme.
X X 12.0 1.05 165 ±
1)
4
Intensive 70°C
Recommended programme for
heavily soiled crockery,
especially suitable for pans and
saucepans.
X X 14.0 1.55 155 ±
1)
5
Half Load 50°C
Ideal for washing a half load of
lightly or normally soiled
crockery.
X X 10.0 1.04 145 ±
1)
