Indesit Markası'nın Ürünleri

Only use products which have been specifically designed

for dishwashers. Do not use table salt or industrial salt.

Follow the instructions given on the packaging.

If you are using a multi-function product, we recommend

that you add salt in any case, especially if the water is hard

or very hard.

(Followtheinstructionsgivenonthepackaging.)

If you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID* indicator lights will remain lit.

Measuring out the refined salt

Theuse of saltprevents the formationof LIMESCALE onthe

dishes and on the machine's functional components.

•Itisimportantthatthesaltdispenserbeneverempty.

•Itisimportanttosetthewaterhardness.

The salt dispenser is located in the lower part of the dishwasher

(seeDescription)

and should be filled:

• WhentheLOWRINSEAIDindicatorlightinthecontrolpanel

is lit *;

• Whenthegreenfloat* on the cap of the salt dispenser is no

longer visible.

• Seeautonomyinthewaterhardnesstable.

1.Removethelowerrackandunscrewthe

containercap(anticlockwise).

2. Only the first time you do this: fill the water

dispenser up to the edge.

3.Position the funnel

(seefigure)

and

fill the salt container right up to its edge

(approximately1kg);itisnotunusualfora

little water to leak out.

4.Removethefunnelandwipeanysaltresidueawayfromthe

opening; rinse the cap under running water and then screw it on.

It is advisable to perform this procedure every time you add salt

to the container.

Make sure the cap is screwed on tightly, so that no detergent can

getintothecontainerduringthewashcycle(thiscoulddamage

the water softener beyond repair).

Whenever you need to add salt, we recommend carrying out

the procedure before the washing cycle is started.

Setting the water hardness

For perfect water softener operation, it is essential that the

adjustment be based on the water hardness in your house. Ask

your local water supplier for this information. The factory setting

is for medium water hardness.

•SwitchthedishwasheronusingtheOn/Offbutton.

•SwitchitoffusingtheOn/Offbutton

•HolddownbuttonP for 5 seconds until you hear a beep.

•SwitchitonusingtheOn/Offbutton

•Thecurrentselectionlevelnumberandsaltindicatorlightflash.

•Press buttonP to select the desired hardness level

(see

hardness table).

•SwitchitoffusingtheOn/Offbutton

•Settingiscomplete!

Refined salt and

rinse aid

(°dH=hardnessmeasuredinGermandegrees-°f=hardness

measuredinFrenchdegrees–mmol/l=millimolesperlitre)

Measuring out the rinse aid

RinseaidmakesdishDRYINGeasier.Therinseaiddispenser

should be filled:

• WhentheLOWRINSEAIDindicatorlightonthepanel/display

is lit *;

• Whenthedarkopticalindicator* on the dispenser door “D”

becomes transparent.

1. Open the dispenser “D” by pressing and pulling up the tab

on the lid;

2.Carefully introduce the rinse aid as far as the maximum

reference notch in the filling space - avoid spilling it. If this

happens, clean the spill immediately with a dry cloth.

3.Presstheliddownuntilyouhearaclicktocloseit.

NEVER pour the rinse aid directly into the tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results, you

may want to adjust the quantity of rinse aid used.

•SwitchthedishwasheronusingtheOn/Offbutton.

•SwitchitoffusingtheOn/Offbutton

•PressbuttonP three times - a beep will be heard.

•SwitchitonusingtheOn/Offbutton

•The current selection level number and rinse aid indicator

light flash.

•PressbuttonP to select the level of rinse aid quantity to be

supplied.

•SwitchitoffusingtheOn/Offbutton

•Settingiscomplete!

Iftherinse aid levelis set toZERO,the rinse aidwill not be

supplied and the low rinse aid indicator light will not be lit if you

run out of it.

Amaximumof4levelscanbesetaccordingtothedishwasher

model. The factory setting is for a medium level.

•Ifyouseebluishstreaksonthedishes,setalownumber(1-2).

•Iftherearedropsofwaterorlimescalemarksonthedishes,

setahighnumber(3-4).

Water Hardness Table

Average autonomy

salt dispenser with 1

wash cycle per day

level °dH °fH mmol/l months

1 0 - 6 0 - 10 0 - 1 7 months

2 6 - 11 11 - 20 1.1 - 2 5 months

3 12 - 17 21 - 30 2.1 - 3 3 months

4 17 - 34 31 - 60 3.1 - 6 2 months

34 - 50 61 - 90 6.1 - 9 2/3 weeks

For values between 0°f and 10°f, we do not recommend the use

of salt. A setting of 5 may increase cycle duration.

* Only available in selected models.